Корзина
Профиком
+380 (68) 854-55-57
Корзина

MR-0133, 2 порта RS485, с собственным источником питания, гальваническая развязка

MR-0133, 2 порта RS485, с собственным источником питания, гальваническая развязка, фото 1
  • MR-0133, 2 порта RS485, с собственным источником питания, гальваническая развязка, фото 2
  • MR-0133, 2 порта RS485, с собственным источником питания, гальваническая развязка, фото 3
  • MR-0133, 2 порта RS485, с собственным источником питания, гальваническая развязка, фото 4
  • MR-0133, 2 порта RS485, с собственным источником питания, гальваническая развязка, фото 5
  • MR-0133, 2 порта RS485, с собственным источником питания, гальваническая развязка, фото 6
  • Под заказ
  • Код: TXN 101 33
clockОтправка с 09 июля 2026

от 8 778 ₴

+380 (68) 854-55-57
Павел
возврат товара в течение 14 дней по договоренности
MR-0133, 2 порта RS485, с собственным источником питания, гальваническая развязкаMR-0133, 2 порта RS485, с собственным источником питания, гальваническая развязка
от 8 778 ₴
Под заказ
+380 (68) 854-55-57
Павел
Описание
Характеристики
Информация для заказа
The MR-0133 submodule contains 2x RS-485 interfaces. The internal connection ensures galvanic separation of the interface from the system and power supply circuits. In the variant with the number TXN 101 33.01, both buses have already connected a 120 Ω terminating resistor. At the same time, the module contains identification circuits. The user has the opportunity to identify the type of submodule used from the development environment.
DI
DI/AI
DO
AI
AO
COM
SENSOR
COM - Serial channels
Number of internal RS-485 serial channels2
Max. baud rate1 MBd
Note on max. SpeedIf the RTS jumper is connected to AUTO, the maximum speed will be 200 kBd, otherwise 2 MBd.
Receiver sensitivity (RS-485)min. ±200 mV
Signal output level (RS-485)typ. 3 V
Max. length of connected line (RS-485)1200 m
Note on cable lengthThe maximum length applies to twisted and shielded cable and communication speed max. 120 kBd.
Power supply
Supply voltage, tolerancesThe submodule is powered from the power supply the terminal device in which it is installed.
Maximum power input1,2 W
Galvanic separation of power supply from internal circuitsNo
Insulation voltage of galvanic separation1 000 VDC
Size and weight
Weight approx.25 g
Product dimensions (width x height x depth)15,5 × 42 × 3,5 mm
Operating conditions, product standards
Product standardČSN EN 61131-2:2008 (idt IEC 61131-2:2007) - Programmable control units
Protection class of electrical objectIII, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016)
IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989)IP20
Operating areasNormal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005)
Degree of pollution1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007)
Overvoltage category installationII, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007)
Type of deviceSubmodule
Type of operation (operating frequency)Continuous
Ambient operating temperatures-20 °C to + 55 °C
Operating temperature maximum (° C)+55°C
Operating temperature minimum (° C)-20°C
Operating relative humidityfrom 10 % up to 95 % without condensation
Operating atmospheric pressuremin. 70 kPa (<3,000 m above sea level)
Storage temperatures–25 °C to +70 °C
Installation
Attention!Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to touch the printed circuit boards directly without protective measures.
Connection
DescriptionTerminal communication interfaces are typically equipped with connectors. The connection of the connectors is specified in the documentation of the respective system where the submodule is used.
Module operation
Module configurationSubmodules with an RS-485 interface contain solder jumpers, which are used to connect a terminating resistor network. They are marked "BT1" for the first channel and "BT2" for the second channel. By default, submodules are shipped with jumpers disconnected.
Warranty
GenerallyWarranty and complaint conditions are governed by the Terms and Conditions of Teco a.s.
WarningAll conditions of this documentation must be met before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery of which the Foxtrot system is a part complies with the requirements of Directive 89/392 / EEC, in so far as it applies to them. Documentation subject to change.
Основные
ПроизводительTeco
Страна производительЧехия
СостояниеНовое
  • Цена: от 8 778 ₴