CP-2005 LTE - процессор, 2x Ethernet, 6 AI/DI, 6 RO, 2 AO, CIB, TCL2, LCD

CP-2005 is a second-generation Foxtrot basic module, which is an optimal combination of a central unit with an integrated combination of 12 digital and analog inputs and outputs, compact size occupying a width of 6 modules on a DIN rail. It is thus possible to have a variant with a built-in LTE modem for direct connection to the Internet via a mobile operator. Of course, there are masters of both system expansion buses - TCL2 (up to 10 addressable modules) and two-wire CIB Common Installation Bus® (up to 32 addressable modules). It can therefore be extended in the same way as other basic modules. It is equipped with a total of 12 I / Os:     six multipurpose inputs, each of which can be used either as analog or as binary     two analog outputs for proportional control of various connected devices.     six separate relay outputs organized into two groups of three with their own common terminal Communication capabilities of the basic module CP-2005:     2x Ethernet interface 100 Mbit / s, each with up to 32 simultaneous connections (programming and general IP communication)     USB micro (programming)     USB A for Flas memory, WiFi adapter (client and AP - Access point) etc.     Variant with built-in LTE modem for direct wireless connection to the Internet via a mobile network operator     Slots for up to 4 optional serial interfaces RS-485, RS-232 24 V DC power supply, possibility of direct connection of a backup battery for uninterrupted operation in case of 230 V AC mains failures. CP-2005 is equipped with a new powerful central unit (CPU series L) with memory     1 MB for user program,     128 MB internal disk for storing files with parallel access from the LAN as a network disk,     16MB fast RAM disk     128/256 kB Datalobox     microSD card slot up to 1 TB     File management is provided by a journaling file system     Local communication with the user via OLED display (4 lines / graphic) and 6-key keyboard

DI	3x DI/HSC
DI/AI	6x DI/AI
DO	6x RO
AI
AO	2x AO
COM	2x ETH 10/100 4x Serial channel (2x free slot) 1x USB device 1x USB host 1x TCL2 master 1x CIB master
SENSOR

System parameters of the central unit
Row of central unit	I
User program memory	1 MB
Memory for user variables / including RETAIN variables	320 kB/48 kB
Instruction length	4 Byte
Backup of program source code in PLC	Yes, optional in Mosaic
On-line program change in PLC	Yes, including I / O configuration change
DataBox - additional internal data memory	128/257 kB, optional
File system - Internal Drive in PLC	128 MB, journaling file system
File system - RAM disk PLC	16 MB
File System - USB Flash Drive	Supported
File system - Micro SD card	supported (except for variants with WLAN1)
Optional memory card slot	microSD - Card Slot (<= 1TB)
Cycle time per 1k of logic instructions	0,036 ms
Cycle time for 1k integer operations	0,044 ms
Cycle time for 1k floating point operations	0,043 ms
Development environment	Mosaic v2018.2 or higher
Programming languages	ST, IL, LD, FBD, SFC, CFC
RTC - Real time circuit	No
RTC - Backup time	typ. 500 hours
Integrated Web server	Yes
Integrated Datalogger	Yes
Access to PLC variables via web API	Yes
COM - Communication - IP/Ethernet
Ethernet 10/100 Mb (ETHx)	2
WLAN1 (internal, optional)	1
WLAN2 (external via USB host, optional)	1
LTE interface (LTEx, optional)	1
Available system modes on ETH and WLAN	UNI, PC, PLC, PLD
Available system modes on LTE	UNI - Exchange over UDP, TCP and support SSL / TLS encryption PC - EPSNET UDP / EPSNET TCP
TCP / IP protocol	Yes
UDP protocol	Yes
HTTPS protocol	Yes
HTTP protocol	Yes
WebSocket protocol	Yes
Protocol MODBUS/TCP	Yes
SMTP protocol	Yes
IEC 60870-5-104 protocol	Yes
REST API	Yes
COM - USB
USB devices interface	1x micro-USB
USB host interface	1x USB-A
Available system modes on USB	PC
COM - Serial channels
max. number of optional serial channels in the basic module	4
number of slots for optional submodules with interface (MR-013x)	2
max. number of expanding serial channels on the TCL2 bus	6
Available system modes on CH5-10	UNI, CSJ (CAN)
Modbus RTU / ASCII master protocol	No
Modbus protocol RTU/ASCII slave	No
Profibus DP master protocol (<180 kbit/s)	No
COM - System buses
TCL2 - system I/O bus	1x TCL2 master
TCL2 - Range of one branch of the system I/O bus	10 I / O modules + 4 operator panels + 6 serial channels
CIB - Common Installation Bus (R): Installation I/O bus	1x CIB master (100 mA)
CIB - Address range of one branch of the installation bus	32 CFox I/O modules
DI - Parameters of binary inputs DC (group A)
Number of inputs in group	14
Common wire	minus
Input type	Type 1 (IEC)
Galvanic isolation of inputs from internal/peripheral circuits	No
Diagnostics	indication of energized input by LED on module panel
Pulse input overload capacity	max. 30 V (t < 10 ms)
Input voltage for log. 0	0 V DC; -5 V DC min.; +5 V DC max.
Input voltage for log. 1	24 V DC; 15 V DC min.; 30 V DC max.
Input current at log. 1 (typ.)	5 mA typ.
Delay from log. 0 to log. 1	500 μs
Delay from log. 1 to log. 0	500 μs
The minimum width of the captured pulse	500 μs
Notice	Note that the GND terminals in the 24 V DC and ANALOG OUTPUTS arrays they are connected inside the system. It is not desirable to connect the GND terminal in the ANALOG field OUTPUTS with a negative pole power supply system also inputs as it would cross the other the GND terminal has closed the loop and thereby potentially induced interfering signals.
DI - Parameters of binary AC inputs
Total number of binary AC inputs	1
Number of groups of AC inputs	1
Number of AC inputs in group	1
Organization of binary inputs into groups	1x (DI14)
Input type	conventional switch
Galvanic isolation of internal circuits	Yes
Input voltage for log. 0	0 V AC min., 120 V AC max.
Input voltage for log. 1	230 V AC typ., 200 V AC min., 250 V AC max.
Input current at log. 1 (typ.)	5 mA typ.
Delay from log. 0 to log. 1	10 ms
Delay from log. 1 to log. 0	10 ms
HSC - Special functions of binary inputs / counters
Unidirectional counter (UP)	4x (DI4); (DI5); (DI8); (DI9)
PWM input (PWM)	2x (DI4, DI5)
Overview of individual signal abbreviations	UP, UPB - pulse input for counter increment, counter B DOWN, DOWNB - pulse input for counter decrement, counter B CLK, CLKB - pulse input for counter, counters B DIR, DIRB - counter direction, counters B CLR - resetting the counter CAP - capture the counter value V - IRC's first track G - IRC second track NI - IRC zero pulse MD - measuring contact
HSC - Counter input parameters
Counter: Input frequency / resolution	1 kHz
Pulse width	min. 500 μs
Delay from log. 0 per log. 1	500 μs
Delay from log. 1 per log. 0	500 μs
Range of registers	up to 32 bits, 0 to 4 294 967 296
DO - Parameters of binary transistor outputs (group A)
Number of transistor outputs	2
Number of output groups	1
Number of outputs in group	2
Organization of transistor outputs into groups	2 (DO11/AO0-DO12/AO1)
Common group conductor	minus
Output type	MOSFET (Low-side switch)
Galvanic separation from internal circuits	No
Switching voltage	5 - 30 V DC
Switching current, output load	0,5 A max.
Short-term output overload capacity	3 A max.
Output resistance	typ. 0,16 Ω, max. 0,4 Ω
Switching time	typ. 9 μs
Opening time	typ. 13 μs
Internal protection	overvoltage, short circuit and overheating protection
RO - Parameters of binary relay outputs (group A)
Parameters valid for the terminals	DO0–DO5, DO7–DO10
Number of relay outputs	11
Number of output groups	3
Organization of relay outputs into groups	3 (DO0-DO2) +3 (DO3-DO5) +5 (DO6-DO10)
Diagnose	Alarm signaling on panel module
Switching current	3 A max., 100 mA min.
Switching voltage	250 V AC max., 5 V AC min., 30V DC max.
Short-term output overload - inrush	4 A max.
Current through common clamp	10 A max.
Contact closing time	typ. 10 ms
Contact opening time	typ. 4 ms
Limit values of switched resistive load	max. 3A at 30 V DC or 230 V AC
Switching inductive load limits DC13	max. 3 A at 30 V DC
Switching inductive load limits AC15	max. 3 A at 230 V AC
Switching frequency without load	max. 300 switching / min.
Switching frequency with rated load	max. 20 switching / min.
Mechanical life	min. 5,000,000 cycles
Electrical life at maximum resistive load	min. 100,000 cycles
Electrical life at maximum load inductive DC13	min. 100,000 cycles
Electrical life at maximum load inductive AC15	min. 100,000 cycles
Short-circuit protection	No
Treatment of inductive load	External RC element, varistor (AC), diode (DC)
Insulation voltage between outputs and internal circuits	3750 V AC
Isolation voltage between groups of outputs to each other	3750 V AC
RO - Parameters of binary relay outputs (group B)
Parameters valid for the terminals	DO6
Switching current	10 A max., 100 mA min.
Switching voltage	max. 250 V AC; max. 30 V DC; min. 5 V
Short-circuit protection	No
Short-term output overload	10A max.
Current through common clamp	10 A max.
Contact closing time	typ. 10 ms
Contact opening time	typ. 4 ms
Limit values of switched resistive load	max. 10A at 30 V DC or 230 V AC
Switching inductive load limits DC13	max. 10 A at 30 V
Switching inductive load limits AC15	max. 10 A at 230 V AC
Switching frequency without load	max. 300 switching / min.
Switching frequency with rated load	max. 6 switching / min
Mechanical life	min. 5,000,000 cycles
Electrical life at maximum resistive load	min. 100,000 cycles
Electrical life at maximum load inductive DC13	min. 100,000 cycles
Electrical life at maximum load inductive AC15	min. 100,000 cycles
Treatment of inductive load	External RC element, varistor (AC), diode (DC)
Insulation voltage between outputs and internal circuits	3750 V AC
Isolation voltage between groups of outputs to each other	3750 V AC
AI - Organization of analog inputs
Total number of analog inputs	14
Number of inputs per group	14
Number of analog input groups	1
Organization of analog inputs into groups	12 (DI0/AI0-DI5/AI5) (DI8/AI8-DI13/AI13) + 2 (DI6/AI6/AO2-DI7/AI7/AO7)
Input type	With common clamp
Common wire	Minus
Galvanic separation from internal circuits	No
Diagnostics	overload signaling in status word
External power supply	No
Digital resolution	12 bit
Converter type	Approximation
conversion time	20 μs
Operating modes	periodic input sensing
Filtration	low pass filter, digital comb filter 50/60 Hz
Insulation potential	500 V DC between input and internal circuits
AI - Analog Input Ranges (Group A)
Voltage	0 to 2 V / 805.9 μV
Input impedance in the voltage signal range	> 20 kΩ
Voltage input error - max. error at 25 ° C	± 0.4% of full scale
Voltage input error - temperature coefficient	± 0.03% of full scale / K
Voltage input error - non-linearity	± 0.07% of full scale
Voltage input error - repeatability under steady state conditions	0.05% of full scale
Permissible continuous overload - voltage input	-20 V to +30 V
Ccurrent	0 to 20 mA / 8,059 μA
Current	4-20 mA
Input impedance in the current signal range	100 Ω
Current input error - maximum error at 25 ° C	±0.4% of full scale
Error current input - temperature coefficient	± 0.03% of full scale / K
Error current input - nonlinearity	± 0.07% of full scale
Error current input - repeatability at steady-state conditions	0.07% of full scale
Permissible continuous overload - current input, resistance 100 R	± 5 V / 50 mA max
Open input detection	Yes, in status word (under-range - only 4 - 20 mA range)
Passive sensor	NTC Thermistor 20k / 25 °C (-40 to + 125 °C)
Input impedance in signal range RTD	> 20 kΩ
Resistance measurement error - maximum error at 25 ° C	± 0.5% of full scale
Resistance measurement error - temperature coefficient	± 0.05% of full scale / K
Resistance measurement error - non-linearity	± 0.09% of full scale
Resistance measurement error - repeatability at steady conditions	0.07% of full scale
Detection of disconnected sensor	yes, in status word, range overflow
AO - Analog output parameters
Number of outputs in group	4
Organization of outputs in groups	2 (DO11/AO0-DO12/AO1) + 2 (DI6/AI6/AO2-DI7/AI7/AO3)
Common wire of group	minus
Galvanic isolation from internal circuits	No
Output type	active voltage output
Converter resolution	12 bit
conversion time	10 μs
Analog output error - maximum error at 25 ° C	± 2% of full scale
Analog output error - temperature coefficient	± 0.3% of full scale / K
Analog output error - linearity	± 0.7% of full scale
Analog output error - repeatability under steady state conditions	± 0.5% of full scale
Voltage output - voltage	0 - 10,5 V
Voltage output - Resolution 1 LSB	2,589 mV
Voltage output - maximum output current	10 mA
Power supply
Supply voltage, tolerances	24 V DC, +25%, -15%, SELV
Maximum power input	10 W
Module thermal/power loss	12 W
Internal protection	Yes, PTC reversible fuse
Power supply from ETH, passive PoE - input (appliance)	ETH1/Power In
Power supply from ETH, passive PoE - output (source)	ETH2 / Power out, jumper configuration
Power supply from ETH, passive PoE - injector parameters	24 V DC, 1A
Size and weight
Weight approx.	300 g
Product dimensions (width x height x depth)	158 x 90 x 62 mm
Module width in multiples of M (17.5 mm)	9M
Operating conditions, product standards
Product standard	ČSN EN 61131-2:2008 (idt IEC 61131-2:2007) - Programmable control units
Protection class of electrical object	II, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016)
IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989)	IP20
Operating areas	Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005)
Degree of pollution	1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007)
Overvoltage category installation	II, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007)
Type of device	Module on DIN rail
Working position	Vertical
Type of operation (operating frequency)	Continuous
Ambient operating temperatures	-20 °C to + 55 °C
Operating temperature maximum (° C)	+55°C
Operating temperature minimum (° C)	-20°C
Operating relative humidity	from 10 % up to 95 % without condensation
Operating atmospheric pressure	min. 70 kPa (<3,000 m above sea level)
Storage temperatures	–25 °C to +70 °C
Electromagnetic compatibility, Mechanical endurance
Electromagnetic compatibility / Emission	B, according to EN 55032 ed. 2: 2017 (idt CISPR 32: 2015)
Emmisions - note	In premises where the use of radio and television receivers can be expected to be used a distance of 10 m from these devices may cause radio interference. In such a case, the user may be required to take appropriate action.
Electromagnetic compatibility / Immunity	min. as required by EN 61131-2: 2007
Sinusoidal vibration endurance	10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.)
Packaginng, transportation, storage
Description	The module is packed in a paper box according to the internal packing instructions. The package includes the following documentation. The outer packaging is carried out according to the scope of the order and the method of transport to the transport a package bearing the transport labels and other particulars necessary for transport. Transport from the manufacturer is carried out in the manner agreed upon when ordering. Product transport the customer's own means must be carried out by covered means of transport, in the specified position label on the packaging. The box must be stowed so as to prevent spontaneous movement a damage to the outer packaging. The product must not be exposed to direct weathering during transport and storage influences. Transport is allowed at temperatures from -25 ° C to +70 ° C, relative humidity 10% up to 95% (non-condensing) and a minimum atmospheric pressure of more than 70 kPa. Storage of the product is only allowed in clean rooms without conductive dust, aggressive gases and vapors. The most suitable storage temperature is 20 ° C
Installation
Assembly description	The basic module is mounted vertically on the U-rail ČSN EN 50022. The installation of the assembly (basic module and peripheral modules, if applicable) is performed according to TXV 004 50.
Exchangeable submodules	The optional MR-013x submodules of the serial interface are mounted in the base module CP-2007 on the bottom plate, which is accessible after removing the bottom of the housing. We only handle the module without power supply!
Connection
Connection of power and system communication	connector with 2.5 mm2 screw terminal
Connection of inputs / outputs	connector with screw terminal 2.5 mm2
Ethernet	RJ-45
Serial channels	screw-type connector 9x 1.5 mm2
USB device connection	type micro B
USB host connection	type A
Module operation
Module configuration	The module is operated, set and diagnosed from the MOSAIC programming environment. It is also possible to connect to the PLC using a web browser on port 8080. If the PLC has an IP address set eg 192.168.134.178 (default address on port ETH1, port ETH2 has DHCP enabled), just enter the address in the form http://192.168.134.178:8080 and the web browser displays the PLC configuration pages.
Commissioning	The module is ready for operation after connection of the supply voltage. The MODE button is available on the module panel to display the currently set IP address of the Ethernet interface. Parameters of all interfaces are set in the Mosaic programming environment. The exact setup procedure is given in the TXV 004 50 documentation.
Module diagnostics	The basic diagnostic system of the module is part of its standard software. It operates from module power on and operates independently of the user. Diagnostic error states of the module and connected peripheral modules of the assembly are signaled on the module display and are available for processing by the master system. For more information, see TXV 004 50.
Maintenance
Description	The module does not require any maintenance under general installation conditions.
Notice	Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!!
Warranty
Generally	Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s.
Notice	You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change.