IT-1605, 8 входных каналов: 16 бит, дифференциальный: термопары J, K, R, (S), B; 2 выходных канала: 10 бит / 0–10 В, GO

The expansion module IT-1605 contains 8 analog differencial inputs and 2 analog outputs with a common terminal. The inputs are universal, independently configurable as voltage inputs for low voltage or for the measuring of thermocouples. The resolution of inputs is 16 bits. The module ensures the measuring and the conversion of the measured value to the engineering units. Voltage analog outputs can be used in the range from -10 V to +10 V and the resolution is 10 bits. The inputs and outputs are galvanically separated from the power supply and TCL2 communication line. The status of each input is indicated by LEDs on the module. The module is equipped with removable screw-type terminals.

DI
DI/AI
DO
AI	8x AI
AO	2x AO
COM	1x TCL2
SENSOR

COM - System buses
TCL2 - system I/O bus	1x TCL2 slave
AO - Analog output parameters
The number of groups of analogue outputs	1
Number of outputs in group	4
Number of outputs and their organization into groups	4x AO (UO0/IO0-UO3/IO1)
Parameters valid for the terminals	UO0/IO0 - UO3/IO3
Common wire of group	AGND terminal
Galvanic isolation from internal circuits	No
Output type	active voltage output
Disconnected output detection	Yes current loop from 0.1 mA
Overload signaling	No
Max. permissible permanent overload (without damage)	(-1 V) to (+ Vao + 1V) each terminal against AGND
Converter resolution	12 bit
Analog output error - maximum error at 25 ° C	± 0.3% of full scale
Output repeat setting time	typ. 0,5 ms
Analog output error - temperature coefficient	± 0.05% of full scale/K
Analog output error - linearity	± 0.1% of full scale
Analog output error - repeatability under steady state conditions	± 0.5% of full scale
External power supply	typ. 24 V DC
External power supply - tolerance	- 25 ÷ +20%
External power supply - max. Current consumption	135 mA
Voltage output - voltage	±10,5 V
Voltage output - maximum output current	10 mA
Voltage output - short-circuit output current	12 mA
Current output - range	0 ÷ 20 mA
Current output - current loop resistance	0 ÷ 600 Ω
Power supply
Nominal supply voltage (V)	24 V DC
Supply voltage, tolerances	24 V DC, +25 %, –15 %
Typical power input	1 W
Maximum power input	4,5 W
Module thermal/power loss	4,5 W
Galvanic separation of power supply from internal circuits	No
Internal protection	No
Size and weight
Weight approx.	125 g
Product dimensions (width x height x depth)	52 x 90 x 58 mm
Module width in multiples of M (17.5 mm)	3M
Operating conditions, product standards
Product standard	ČSN EN 61131-2:2008 (idt IEC 61131-2:2007) - Programmable control units
Protection class of electrical object	II, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016)
IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989)	IP20
Operating areas	Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005)
Degree of pollution	1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007)
Overvoltage category installation	II, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007)
Type of device	Module on DIN rail
Working position	Vertical
Type of operation (operating frequency)	Continuous
Ambient operating temperatures	-20 °C to + 55 °C
Storage temperatures	–25 °C to +70 °C
Electromagnetic compatibility, Mechanical endurance
Electromagnetic compatibility / Emission	A, according to EN 55032 ed. 2: 2017 (idt CISPR 32: 2015)
Emmisions - note	In premises where the use of radio and television receivers can be expected to be used a distance of 10 m from these devices may cause radio interference. In such a case, the user may be required to take appropriate action.
Electromagnetic compatibility / Immunity	min. as required by EN 61131-2: 2007
Sinusoidal vibration endurance	10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.)
Packaginng, transportation, storage
Description	The module is packed in a paper box according to the internal packing instructions. This documentation is also part of the package. The outer packaging is carried out according to the scope of the order and the method of transport in a transport package provided with transport labels and other data necessary for transport. Transport from the manufacturer is carried out in the manner agreed upon when ordering. The transport of the product by the customer's own means must be carried out by covered means of transport, in the position determined by the label on the packaging. The box must be stored in such a way that it does not move spontaneously and the outer packaging is not damaged. The product must not be exposed to direct weather conditions during transport and storage. Transport is permitted at temperatures of -25 ° C to 70 ° C, relative humidity of 10% to 95% (non-condensing) and a minimum atmospheric pressure higher than 70 kPa. The product may only be stored in clean rooms free of conductive dust, aggressive gases and vapors. The most suitable storage temperature is 20 ° C.
Installation
Assembly description	The basic module is mounted in a vertical position on the U-rail ČSN EN 50022. The installation of the assembly (basic module and possibly peripheral modules) is performed according to TXV 004 10.
Connection
Connection description	Wiring notes: 1. The analog output can be used on either channel either voltage or current, not both at the same time. 2. In the connection example, 2 ways of load connection are shown. They can be combined with each other. 3. The selection of the analog output type is performed in the Mosaic environment. 4. It is recommended to use shielded wires to connect the analog outputs. 5. Voltage for analog outputs can be changed according to the table of electrical parameters (chapter 1.3)
Connection of power and system communication	connector with 2.5 mm2 screw terminal
Connection of inputs / outputs	connector with screw terminal 2.5 mm2
Module operation
Module configuration	The module is operated, set up and diagnosed from the Mosaic development environment.
Commissioning	The module is ready for operation after connecting the supply voltage. The MODE button is available on the module panel to display the currently set Ethernet IP address. The parameters of all interfaces are set in the Mosaic development environment.
Module diagnostics	The basic diagnostic system of the module is part of its standard software. It has been in operation since the module power was turned on and works independently of the user. Diagnosed module error states are listed in TXV 004 10.
Maintenance
Description	The module does not require any maintenance under general installation conditions. The operations in which a part of the module has to be dismantled must always be carried out with the supply voltage disconnected.
Notice	Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!!
Warranty
Generally	Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s.
Notice	You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change.