CP-1001 Процессор Ethernet/RS232, 4×AI/DI, 2×DI 230 В переменного тока, 2×RO
Знято з виробництва
- Под заказ
- Код: TXN 110 01
Отправка с 03 октября 2026Цену уточняйте
Минимальная сумма заказа на сайте — 200 ₴
+380 (98) 363-64-36
возврат товара в течение 14 дней по договоренности
CP-1001 Процессор Ethernet/RS232, 4×AI/DI, 2×DI 230 В переменного тока, 2×RO
Цену уточняйте
Под заказОписание
Характеристики
Информация для заказа
⚠️ Товар снят с производства
Эта модель больше не выпускается производителем и недоступна для заказа.
Нужна замена? Пришлите нам артикул, фото оборудования или технические характеристики — мы поможем подобрать современный аналог с совместимыми параметрами.
Помимо подбора современного аналога, для отдельных моделей мы также можем предложить диагностику и, при наличии технической возможности, ремонт или восстановление оборудования.
| DI | 2x DI (230 V AC) |
| DI/AI | 4x DI/AI |
| DO | 2x RO |
| AI | |
| AO | |
| COM | 1x ETH 10/100 1x RS-232 1x free slot for CH2 1x TCL2 master 2x CIB master |
| SENSOR |
| System parameters of the central unit | |
|---|---|
| Row of central unit | L |
| User program memory | 384 + 64 kB |
| Memory for user variables / including RETAIN variables | 192 kB/48 kB |
| Instruction length | 2 ÷ 10 bytes |
| Backup of program source code in PLC | Yes, in program backup memory (EEPROM) |
| On-line program change in PLC | Yes, including I / O configuration change |
| Memory for project archiving - internal | 2 MB |
| DataBox - additional internal data memory | 512 kB |
| Optional memory card slot | SD - Card Slot |
| Cycle time per 1k of logic instructions | 0,2 ms |
| Development environment | Mosaic |
| Programming languages | ST, IL, LD, FBD, SFC, CFC |
| RTC - Real time circuit | Yes |
| RAM and RTC backup 1) without / with backup battery | type. 500 hr / typ. 20,000 hours |
| Integrated Web server | Yes |
| Integrated Datalogger | Yes |
| Access to PLC variables via web API | Yes |
| Notice | 1) Applies to the basic module without power supply, the backup circuits are disconnected when the power supply is switched on 2) The serial interface CH1 is permanently equipped with an RS-485 interface. The serial interface type CH2 to CH4 is selectable via interchangeable submodules |
| COM - Communication - IP/Ethernet | |
| Ethernet 10/100 Mb (ETHx) | 1 |
| Available system modes on ETH and WLAN | UNI, PC, PLC, PLD |
| TCP / IP protocol | Yes |
| UDP protocol | Yes |
| HTTP protocol | Yes |
| Protocol MODBUS/TCP | Yes |
| SMTP protocol | Yes |
| IEC 60870-5-104 protocol | Yes |
| REST API | Yes |
| COM - Serial channels | |
| max. number of optional serial channels in the basic module | 4 |
| max. number of expanding serial channels on the TCL2 bus | 6 |
| Number of internal RS-232 serial channels | 1 |
| Available system modes on CH5-10 | UNI, CSJ (CAN) |
| Modbus RTU / ASCII master protocol | Yes |
| Modbus protocol RTU/ASCII slave | Yes |
| Profibus DP master protocol (<180 kbit/s) | Yes, on serial channels supporting PFB mode |
| COM - System buses | |
| TCL2 - system I/O bus | 2x TCL2 master |
| TCL2 - Range of one branch of the system I/O bus | 10 I / O modules + 4 operator panels + 6 serial channels |
| The communication rate of the system I / O bus | 345 kbps |
| System I / O bus terminating resistor | 120 Ω |
| DI - Parameters of binary inputs DC (group A) | |
| Parameters valid for inputs on the terminals | DI0÷DI7 |
| Number of inputs in group | 8 |
| Common wire | minus |
| Input type | Type 1 (IEC) |
| Galvanic isolation of inputs from internal/peripheral circuits | Yes, all external circuits connected to the module must meet the conditions for SELV circuits |
| Diagnostics | indication of energized input by LED on module panel |
| Input voltage for log. 0 | 0 V DC; -5 V DC min.; +5 V DC max. |
| Input voltage for log. 1 | 24 V DC; 15 V DC min.; 30 V DC max. |
| Input current at log. 1 (typ.) | 5 mA typ. |
| Delay from log. 0 to log. 1 | 500 μs |
| Delay from log. 1 to log. 0 | 500 μs |
| HSC - Special functions of binary inputs / counters | |
| Unidirectional counter (UP) | 2x (DI0); (DI2) |
| Two unidirectional counters (UP / UPB) | 2x (DI0/DI2); (DI2/DI3) |
| Bidirectional counter (UP/DOWN) | 2x (DI0/DI1); (DI2/DI3) |
| Counter with direction control (CLK/DIR) | 2x (DI0/DI1); (DI2/DI3) |
| Bi-directional counter with reset and intercept (UP / DOWN / CLR / CAP) | 1x (DI0/DI1/DI2/DI3) |
| Counter with direction control with reset and latch (CLK / DIR / CLR / CAP) | 1x (DI0/DI1/DI2/DI3) |
| IRC Basic (V/G) | 2x (DI0/DI1); (DI2/DI3) |
| IRC with Zero and Capture (V / G / NI / MD) | 1x (DI0/DI1/DI2/DI3) |
| Measure the pulse length | 4x (DI0,DI1, DI2, DI3) |
| Period measurement | 4x (DI0,DI1, DI2, DI3) |
| DO - Parameters of binary transistor outputs (group A) | |
| Number of transistor outputs | 4 |
| Number of output groups | 1 |
| Number of outputs in group | 4 |
| Output type | semiconductor output, half-bridge (push-pull) |
| Galvanic separation from internal circuits | Yes |
| Diagnostics | indication of energized output by LED on module panel |
| Switching voltage | 12 - 30 V DC |
| Output resistance | type. 0.3 Ω, max. 0.6 Ω |
| Switching time | typ. 1,6 μs |
| Opening time | typ. 0,6 μs |
| Short circuit protection | Yes |
| RO - Parameters of binary relay outputs (group A) | |
| Number of relay outputs | 7 |
| Number of output groups | 3 |
| Output type | electromechanical relay, unprotected output |
| Contact type | NO - Normally Open |
| Diagnose | Alarm signaling on panel module |
| Switching current | 2 A max., 100 mA min. |
| Switching voltage | 250 V AC max., 5 V AC min., 30V DC max. |
| Short-term output overload - inrush | 4 A max. |
| Short-circuit protection | No |
| AI - Organization of analog inputs | |
| Total number of analog inputs | 8 |
| Number of inputs per group | 8 |
| Number of analog input groups | 1 |
| Organization of analog inputs into groups | 8x AI (AI0÷AI7) |
| Input type | With common clamp |
| Common wire | Minus |
| Galvanic separation from internal circuits | Yes, 8 inputs together |
| Diagnostics | overload signaling in status word |
| Type of protection | integrated overvoltage protections |
| External power supply | No |
| Digital resolution | 12 bit |
| Converter type | Approximation |
| conversion time | 20 μs |
| AI - Analog Input Ranges (Group A) | |
| Parameters valid for inputs on the terminals | AI0÷AI7 |
| Voltage | 0 to 0.5 V / 610.4 μV |
| Input impedance in the voltage signal range | > 20 kΩ |
| Voltage input error - max. error at 25 ° C | ± 0.3% of full scale |
| Voltage input error - temperature coefficient | ± 0.02% of full scale / K |
| Voltage input error - non-linearity | ± 0.08% of full scale |
| Voltage input error - repeatability under steady state conditions | 0.05% of full scale |
| Permissible continuous overload - voltage input | -20 V to +30 V |
| Ccurrent | 0 - 20 mA |
| Current | 4-20 mA |
| Current - resolution 1 LSB | 6 μA |
| Input impedance in the current signal range | 100 Ω |
| Permissible continuous overload - current input, resistance 100 R | ± 5 V / 50 mA max |
| Open input detection | No |
| Passive sensor | NTC Thermistor 12k / 25 °C (-40 to + 125 °C) |
| Resistance measurement error - maximum error at 25 ° C | ± 0.5% of full scale |
| AO - Analog output parameters | |
| Number of outputs in group | 4 |
| Common wire of group | minus |
| Galvanic isolation from internal circuits | Yes, along with the entrances |
| Output type | active voltage output |
| Converter resolution | 12 bit |
| Power supply | |
| Nominal supply voltage (V) | 24 V DC |
| Supply voltage, tolerances | 24 V DC, +25%, -15%, SELV |
| Supply voltage when backing up with an external battery | 27 V DC, +10%, –15%, SELV |
| Typical power input | 8 W |
| Maximum power input | 10 W |
| Module thermal/power loss | 10 W |
| Maximum current consumption (mA) | 500 mA |
| Galvanic separation of power supply from internal circuits | Yes |
| Internal protection | Yes, PTC reversible fuse |
| Size and weight | |
| Weight approx. | 300 g |
| Module width in multiples of M (17.5 mm) | 9M |
| Product dimensions (width x height x depth) | 158 x 90 x 62 mm |
| Operating conditions, product standards | |
| Product standard | ČSN EN 61131-2:2008 (idt IEC 61131-2:2007) - Programmable control units |
| Protection class of electrical object | II, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016) |
| IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989) | IP20 |
| Operating areas | Normal according to ČSN 33 2000-1: 2003 (IEC 364-1: 1992 mod) |
| Degree of pollution | 1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007) |
| Overvoltage category installation | II, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007) |
| Type of device | Module on DIN rail |
| Working position | Vertical |
| Type of operation (operating frequency) | Continuous |
| Ambient operating temperatures | -20 °C to + 55 °C |
| Operating relative humidity | from 10 % up to 95 % without condensation |
| Operating atmospheric pressure | min. 70 kPa (<3,000 m above sea level) |
| Storage temperatures | –25 °C to +70 °C |
| Electromagnetic compatibility, Mechanical endurance | |
| Electromagnetic compatibility / Emission | A, according to EN 55032 ed. 2: 2017 (idt CISPR 32: 2015) |
| Emmisions - note | In premises where the use of radio and television receivers can be expected to be used a distance of 10 m from these devices may cause radio interference. In such a case, the user may be required to take appropriate action. |
| Electromagnetic compatibility / Immunity | min. as required by EN 61131-2: 2007 |
| Sinusoidal vibration endurance | 10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.) |
| Packaginng, transportation, storage | |
| Description | The module is packed in a paper box. This documentation is also part of the package. The outer packaging is carried out according to the scope of the order and the method of transport in a transport package provided with labels and other data necessary for transport. The product must not be exposed to direct weather conditions during transport and storage. Malting of the product is only allowed in clean rooms without conductive dust, aggressive gases and vapors. The most suitable storage temperature is 20 ° C |
| Installation | |
| Assembly description | Switchboard mounting |
| Module operation | |
| Commissioning | The module is operated, set and diagnosed from the MOSAIC programming environment or other parameterization software. The module is ready for operation after connecting the supply voltage and the CIB bus. The HW address is indicated on the label on the module. |
| Module diagnostics | The basic diagnostic system of the module is a part of its standard software. It operates from module power on and operates independently of the user. Diagnostic error states of the module and connected peripheral modules of the assembly are signaled |
| Maintenance | |
| Description | The module does not require any maintenance under general installation conditions. The operations in which a part of the module has to be dismantled must always be carried out with the supply voltage disconnected. |
| Notice | Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!! |
| Warranty | |
| Generally | Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s. |
| Notice | You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change. |
| Основные | |
|---|---|
| Производитель | Teco |
| Страна производитель | Чехия |
| Состояние | Новое |
| Пользовательские характеристики | |
| DI | 2x DI (230 V AC) |
| DI/AI | 4x DI/AI |
| DO | 2x RO |
| COM | 1x ETH 10/100 1x RS-232 1x free slot for CH2 1x TCL2 master 2x CIB master |
- Цена: Цену уточняйте