C-EM-0401M-S Счетчик и анализатор качества электроэнергии CIB, 4×U, 4×I, RO

C-EM-0401M; CIB fast electricity meter / quality meter, power supply 230 V AC / DC, 4x U, 4x I - current transformer x: 100 mA, 1x RO The C-EM-0401M-P035 module is a fast 4-quadrant electricity meter / quality meter providing all parameters of the consumed and supplied energy every 200 ms for four phases. It can be used for one three-phase and one single-phase measurement at the same time as well as for four separate single-phase measurements. The measurement is indirect, currents are sensed by current transformers with a unified 100 mA output. Current transformers are not part of the delivery and must be ordered separately according to the required current range from 50 A up to 2400 A .. The module has one relay output controlled by the implemented voltage and frequency protection function. The range of monitored voltage and frequency, including reaction times and recovery time after the cause of protection activation has disappeared, can be set parametrically from the application program in the basic module. The module is designed for a DIN rail switchboard. It is connected to the Foxtrot basic module via a two-wire CIB Common Installation Bus®.

DI
DI/AI
DO	1x RO
AI	4x U (230 V AC) 4x I (100mA AC)
AO
COM	1x CIB slave
SENSOR

COM - Serial channels
Communication interface DALI	1x DALI master
The scope of each DALI line	64 addresses / substations
Insulation voltage between buses	2,5 kV AC
COM - System buses
CIB - Common Installation Bus (R): Installation I/O bus	1x CIB slave
Power supply
Nominal supply voltage (V)	24 V DC
Auxiliary power supply - voltage	The DALI interface of the module is powered by an external 24 VDC source (terminals A3, A4) outside the CIB bus. The module provides galvanic isolation of the DALI bus from other circuits (CIB). The 24 V supply voltage of the module must be galvanically isolated (safe circuit separation) from the power supply of the Foxtrot system and the CIB bus.
Power supply from CIB - typical current consumption (mA)	30 mA
Power supply from CIB - internal protection	Yes, returnable fuse
Size and weight
Weight approx.	70 g
Product dimensions (width x height x depth)	35 x 90 x 58 mm
Module width in multiples of M (17.5 mm)	2M
Module width	35 mm
Module height	90 mm
Module depth	58 mm
Operating conditions, product standards
Product standard	ČSN EN 60730-1 ed. 2:2001 (mod IEC 60730-1:1999)
Protection class of electrical object	III, according to ČSN EN 61140: 2003 (idt IEC 61140: 2001)
IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989)	IP10B
Operating areas	Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005)
Overvoltage category installation	II, acc. ČSN EN 60664-1:2004 (mod IEC 606641:1992)
Type of device	Module on DIN rail
Working position	Any
Type of operation (operating frequency)	Continuous
Ambient operating temperatures	0 ° C to + 70 ° C
Operating temperature maximum (° C)	+70°C
Operating temperature minimum (° C)	0°C
Operating relative humidity	from 10 % up to 95 % without condensation
Operating atmospheric pressure	min. 70 kPa (<3,000 m above sea level)
Storage temperatures	–25 ° C to + 85 ° C
Electromagnetic compatibility, Mechanical endurance
Electromagnetic compatibility / Emission	ČSN EN 55022 ed2:2007 (mod CISPR22:2005)
Electromagnetic compatibility / Immunity	min. according to ČSN EN 60730-1 ed.2: 2001
Sinusoidal vibration endurance	10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.)
Packaginng, transportation, storage
Description	The module is packed in a paper box. This documentation is also part of the package. The outer packaging is carried out according to the scope of the order and the method of transport in a transport package provided with labels and other data necessary for transport. The product must not be exposed to direct weather conditions during transport and storage. Malting of the product is only allowed in clean rooms without conductive dust, aggressive gases and vapors. The most suitable storage temperature is 20 ° C
Installation
Assembly description	Mounting on DIN rail 35 / 7.5 (U) in the switchboard
Connection
Connection of power and system communication	terminal block with screw terminal 2.5 mm2
Cross-section of connected wires fixed (min)	0,35 mm2
Cross-section of connected wires fixed (max)	2,5 mm2
Cross-section of connected wires stranded (min)	0,35 mm2
Cross-section of connected wires stranded (max)	2,5 mm2
Module operation
Module configuration	The module is operated, set up and diagnosed from the Mosaic development environment.
Maintenance
Description	The module does not require any maintenance under general installation conditions.
Notice	Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!!
Warranty
Generally	Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s.
Notice	You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change.