C-DM-0001B-SL Контроллер адресной RGB LED-ленты WS2812 (CIB)

C-DM-0001B-SL is a module connectable to the CIB bus of the Foxtrot system. It contains one DO output for data addressable RGB LED chips type WS2812B, one IN / OUT terminal for synchronization of several modules in a row and a voltage source of 5 V / 1 A for powering a series of up to 16 LEDs. It is equipped with a slot for a microSD card, on which data files for static and dynamic effects are uploaded. which the module "reads" and cyclically sends to a series of connected LED chips.

DI
DI/AI
DO	1x DO (data) 1x SYN (in/out)
AI
AO
COM	1x CIB slave
SENSOR

COM - System buses
CIB - Common Installation Bus (R): Installation I/O bus	1x CIB slave
DI - Parameters of binary inputs DC (group A)
Parameters valid for inputs on the terminals	DI/AI1, DI/AI2
Number of inputs in group	2
Common wire	minus
Combined input type	DI/AI Active, for sensing potential-free contacts and measuring resistance sensors
Galvanic isolation of inputs from internal/peripheral circuits	No
Balanced resistance input	2× 1k1 (tamper/0/1/tamper)
RO - Parameters of binary relay outputs (group A)
Parameters valid for the terminals	DO1
Number of relay outputs	1
Output type	electromechanical relay, unprotected output
Contact type	NO - Normally Open
Switching current	3 A max., 100 mA min.
Switching voltage	250 V AC max., 5 V AC min., 30V DC max.
Mechanical life	min. 5,000,000 cycles
Electrical life at maximum resistive load	min. 200,000 cycles
Short-circuit protection	No
Treatment of inductive load	External RC element, varistor (AC), diode (DC)
Insulation voltage between outputs and internal circuits	3750 V AC
AI - Organization of analog inputs
Total number of analog inputs	2
Number of inputs per group	2
Number of analog input groups	1
Input type	With common clamp
Common wire	GND terminal
Galvanic separation from internal circuits	No
Diagnostics	overload signaling in status word
Digital resolution	10 bit
AI - Analog Input Ranges (Group A)
Parameters valid for inputs on the terminals	DI/AI1, DI/AI2
Passive sensor	NTC Thermistor 12k / 25 °C (-40 to + 125 °C)
DI: Voltage-free contact	0 when> 1.5 kOhm, 1 when <0.5 kOhm
DI: Balanced resistance input	2x 1k1 (tamper/0/1/tamper)
Resistance measurement error - maximum error at 25 ° C	± 0.5% of full scale
AO - Analog output parameters
Galvanic isolation from internal circuits	No
Output type	active voltage output
Voltage output - voltage	0 - 10 V
Voltage output - Minimum resolution	1 %
Voltage output - Adjustable range	0 ÷ 130 % Ujm
Voltage output - Load resistance	>1 kΩ
Voltage output - Load capacity	250 nF
Power supply
Supply voltage, tolerances	24/27 V DC from CIB bus
Power supply from CIB - typical current consumption (mA)	18 mA
Power supply from CIB - maximum current consumption (mA)	25 mA
Power supply from CIB - Galvanic separation of power supply from internal circuits	Relay output contact only
Insulation voltage of galvanic separation	4 000 VAC (50/60 Hz) 1 min.
Insulation resistance	1 MΩ min. (at 500V)
Power supply from CIB - internal protection	Yes, returnable fuse
Size and weight
Weight approx.	7 g
Module width	55 mm
Module height	26 mm
Module depth	20 mm
Product dimensions (width x height x depth)	55 x 26 x 20 mm
Operating conditions, product standards
Product standard	ČSN EN 60730-1 ed. 2:2001 (mod IEC 60730-1:1999)
Protection class of electrical object	III, according to ČSN EN 61140: 2003 (idt IEC 61140: 2001)
IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989)	IP10B
Operating areas	Normal according to ČSN 33 2000-1: 2003 (IEC 364-1: 1992 mod)
Degree of pollution	1, according to ČSN EN 60664-1: 2004 (mod IEC 60664-1: 1992)
Overvoltage category installation	II, acc. ČSN EN 60664-1:2004 (mod IEC 606641:1992)
Type of device	In the installation box, under the cover
Working position	Any
Type of operation (operating frequency)	Continuous
Ambient operating temperatures	0 °C to + 55 °C
Operating temperature minimum (° C)	0°C
Operating relative humidity	from 10 % up to 95 % without condensation
Operating atmospheric pressure	min. 70 kPa (<3,000 m above sea level)
Storage temperatures	–25 °C to +70 °C
Electromagnetic compatibility, Mechanical endurance
Electromagnetic compatibility / Emission	B, according to EN 55022: 1999 (mod CISPR22: 1997)
Electromagnetic compatibility / Immunity	min. according to ČSN EN 60730-1 ed.2: 2001
Sinusoidal vibration endurance	10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.)
Packaginng, transportation, storage
Description	Модуль упакован в антистатический пакет. Эта документация также является частью пакета. Внешняя упаковка осуществляется в соответствии с объемом заказа и способом транспортировки в транспортной упаковке, снабженной этикетками и другими данными, необходимыми для транспортировки. Продукт не должен подвергаться воздействию прямых погодных условий во время транспортировки и хранения. Соложение продукта разрешено только в чистых помещениях. без токопроводящей пыли, агрессивных газов и паров. Наиболее подходящая температура хранения - 20 ° C.
Installation
Assembly description	The module is inserted freely into the installation box or attached with a suitable cable tie inside the device. The conductors of the supply ribbon cable can be separated and shortened as required. However, to prevent interference problems, the active conductors must be routed together with the common GND conductor to the sensor so that no interference loops form between the conductors. Best with twisted pair cables.
Connection
Connection of power and system communication	Ribbon flat conductors 0.15 / 0.5 mm2
Module connection	Strip wires 0.15 mm2, relay 2x 0.5 mm2
Module operation
Commissioning	The module is operated, set and diagnosed from the MOSAIC programming environment or other parameterization software. The module is ready for operation after connecting the supply voltage and the CIB bus. The HW address is indicated on the label on the module.
Module diagnostics	The basic diagnostics is performed internally and the result is available in the relevant registers of the Mosaic environment.
Maintenance
Description	The module does not require any maintenance under general installation conditions.
Notice	Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!!
Warranty
Generally	Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s.
Notice	You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change.