C-WS-0200R-Logus Настенный кнопочный модуль CIB Logus, 2 кнопки, 2×AI/DI, датчик температуры
- Под заказ
- Код: TXN 133 56
Отправка с 04 октября 2026Цену уточняйте
Минимальная сумма заказа на сайте — 200 ₴
+380 (98) 363-64-36
возврат товара в течение 14 дней по договоренности
C-WS-0200R-Logus Настенный кнопочный модуль CIB Logus, 2 кнопки, 2×AI/DI, датчик температуры
Цену уточняйте
Под заказОписание
Характеристики
Информация для заказа
C-WS-0200R-Logus is a controller with 2 short-way buttons with red and green LED signaling with 1x internal temperature sensor on the CIB Common Installation Bus®, to which 2 external temperature sensors or contacts can be connected.
| DI | 2x button |
| DI/AI | 2x DI/AI |
| DO | 1x green LED 1x LED red |
| AI | |
| AO | |
| COM | 1x CIB slave |
| SENSOR | 1x temperature |
| Parameter des Temperatursensors | |
|---|---|
| Temperature - Sensor type | NTC 12k |
| Contact parameters | |
| Maximum switching voltage | 27 V DC |
| LED indication parameters | |
| Maximum LED current | 25 mA |
| Size and weight | |
| Weight approx. | 70 g |
| Product dimensions (width x height x depth) | 86 × 86 × 38 mm |
| Operating conditions, product standards | |
| IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989) | IP10B |
| Operating areas | Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005) |
| Degree of pollution | 1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007) |
| Overvoltage category installation | II, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007) |
| Type of device | In the installation box on the wall |
| Working position | Vertical |
| Type of operation (operating frequency) | Continuous |
| Ambient operating temperatures | 0 °C to + 55 °C |
| Operating relative humidity | from 10 % up to 95 % without condensation |
| Operating atmospheric pressure | min. 70 kPa (<3,000 m above sea level) |
| Storage temperatures | –25 °C to +70 °C |
| Installation | |
| Assembly description | The module is mounted in a vertical position on a standard installation box with a spacing of fixing screws of 60 mm. Method: 1. screw the support plate to the installation box (pay attention to the position) 2. connect the wires to the connector 3. attach the frame to the installation box and snap the module into place 4. click the fingerboards |
| Connection | |
| Connection of inputs / outputs | terminal block with spring clamp 0.15-0.5 mm2, push-in |
| Module connection | The S-WS-0200R module is intended for connection to the module on the CIB bus C-IT-0504S (TXN 133 26) or C-IT-0908S (TXN 133 52). It can also be connected to other inputs and outputs while maintaining the polarity of the inputs and outputs. The LED outputs can also be switched by analog outputs, which supply 10 mA at 10 V. The configuration of inputs and outputs is performed in the superior module. |
| Maintenance | |
| Description | The module does not require any maintenance under general installation conditions. The operations in which a part of the module has to be dismantled must always be carried out with the supply voltage disconnected. |
| Warranty | |
| Generally | Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s. |
| Notice | You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change. |
| Основные атрибуты | |
|---|---|
| Производитель | Teco |
| Страна производитель | Чехия |
| Состояние | Новое |
| Пользовательские характеристики | |
| DI | 2x button |
| DI/AI | 2x DI/AI |
| DO | 1x green LED 1x LED red |
| COM | 1x CIB slave |
| SENSOR | 1x temperature |
- Цена: Цену уточняйте