IB-8305, 12 входів, 230 В змінного струму, тип 1;
- Під замовлення
- Код: TXN 183 05
Відправка з 09 липня 2026Ціну уточнюйте
Мінімальна сума замовлення на сайті — 200 ₴
+380 (68) 854-55-57
Павлоповернення товару протягом 14 днів за домовленістю
IB-8305, 12 входів, 230 В змінного струму, тип 1;
Ціну уточнюйте
Під замовленняОпис
Характеристики
Інформація для замовлення
The IB-8305 module is intended for sensing 12 binary signals of 230 V AC with a common terminal, type 1. The module is equipped with a connector with screwless terminals.
| DI | 12xDI |
| DI/AI | |
| DO | |
| AI | |
| AO | |
| COM | 1x TCL3 |
| SENSOR |
| COM - System buses | |
|---|---|
| TCL3 - system I/O bus | 1x TCL3 slave |
| DI - Organization of binary inputs | |
| Total number of binary inputs | 32 |
| Number of groups of binary inputs | 1 |
| Organization of binary inputs into groups | 32x DI (DI0-DI31) |
| DI - Parameters of binary inputs DC (group A) | |
| Parameters valid for inputs on the terminals | DI0-DI31 |
| Number of inputs in group | 32 |
| Common wire | minus |
| Input type | Type 3 (IEC) |
| Galvanic isolation of inputs from internal/peripheral circuits | Yes |
| Galvanic isolation of inputs from peripheral circuits | Yes |
| Diagnostics | indication of energized input by LED on module panel |
| Pulse input overload capacity | -30V/1s, -15V permanently, +40V/1s |
| Input voltage for log. 0 | 0 V DC; -5 V DC min.; +5 V DC max. |
| Input voltage for log. 1 | 24 V DC; 11 V DC min.; 30 V DC max. |
| Input current at log. 1 (typ.) | 2,3 mA typ. |
| Delay from log. 0 to log. 1 | 5 ms |
| Delay from log. 1 to log. 0 | 5 ms |
| The minimum width of the captured pulse | 1 ms |
| Power supply | |
| Supply voltage UVM, UVIO, nominal value | 24 V DC |
| Supply voltage UVM, UVIO, allowed range | 20 - 30 V DC |
| IVM supply current at UVM = 24 V | 10 mA |
| Max. power consumption at the VM level | 0,2 W |
| External power supply of input circuits - voltage | 24 V DC |
| Current consumption of one group from an external source, max. | 13 mA |
| Module thermal/power loss | 2,4 W |
| Size and weight | |
| Weight approx. | 70 g |
| Product dimensions (width x height x depth) | 24 x 118 x 97 mm |
| Operating conditions, product standards | |
| Product standard | ČSN EN 61131-2:2008 (idt IEC 61131-2:2007) - Programmable control units |
| Protection class of electrical object | III, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016) |
| IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989) | IP20 |
| Operating areas | Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005) |
| Degree of pollution | 2, according to ČSN EN 60664-1 ed.2: 2008 (idt IEC 60664-1: 2007) |
| Overvoltage category installation | II, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007) |
| Type of device | Built-in |
| Working position | Vertical |
| Type of operation (operating frequency) | Continuous |
| Ambient operating temperatures | -20 °C to + 55 °C |
| Operating relative humidity | from 10 % up to 95 % without condensation |
| Operating atmospheric pressure | min. 70 kPa (<3,000 m above sea level) |
| Storage temperatures | –25 °C to +70 °C |
| Storage relative humidity | Max. 80% without vapor condensation |
| Storage environment | Dry, clean areas without conductive dust, aggressive gases or acid vapors for a period not exceeding the warranty period. |
| Transport temperatures | -25°C to -70°C |
| Transport environment | Covered means of transport, transport packaging must not be exposed to the effects of rain and snow |
| Electromagnetic compatibility, Mechanical endurance | |
| Electromagnetic compatibility / Emission | A, according to EN 55032 ed. 2: 2017 (idt CISPR 32: 2015) |
| Emmisions - note | In premises where the use of radio and television receivers can be expected to be used a distance of 10 m from these devices may cause radio interference. In such a case, the user may be required to take appropriate action. |
| Electromagnetic compatibility / Immunity | min. as required by EN 61131-2: 2007 |
| Sinusoidal vibration endurance | 10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.) |
| Packaginng, transportation, storage | |
| Description | The module is packed in a paper box. This documentation is also part of the package. The outer packaging is carried out according to the scope of the order and the method of transport in a transport package provided with labels and other data necessary for transport. The product must not be exposed to direct weather conditions during transport and storage. Malting of the product is only allowed in clean rooms without conductive dust, aggressive gases and vapors. The most suitable storage temperature is 20 ° C |
| Installation | |
| Assembly description | The installation of the TC800 system module is carried out by sliding it perpendicularly onto the DIN rail ČSN EN 50022 with busbar and locking latch in the lower part of the module. A more detailed description and mechanical drawings with dimensions are given in the documentation TXV 004 72. |
| Connection | |
| Warning | All external circuits connected to the module must meet the conditions for SELV circuits! |
| Connection description | An example of module connection is shown in the following figure. |
| Power connection | Via system bus + I/O connector |
| Connection of inputs / outputs | Strip wires 0.15 / 0.5 mm2 |
| Connector coding | No |
| Module installation tools | Without tools |
| Module operation | |
| Module configuration | The module is operated, set up and diagnosed from the Mosaic development environment. |
| Commissioning | On the module, the DIP switch in the left part of the case sets a unique address within one frame. The module is fully ready for operation after inserting it into the frame and turning on the power supply. |
| Module diagnostics | The basic diagnostic system of the module is part of its standard software. It has been in operation since the module power was turned on and works independently of the user. Diagnosed error states of the module and connected peripheral modules of the assembly are signaled in the status word of the module and on the module panel |
| Maintenance | |
| Description | The module does not require any maintenance under general installation conditions. The operations in which a part of the module has to be dismantled must always be carried out with the supply voltage disconnected. |
| Notice | Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!! |
| Warranty | |
| Generally | Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s. |
| Notice | You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change. |
| Основні | |
|---|---|
| Виробник | Teco |
| Країна виробник | Чехія |
| Стан | Новий |
| Користувальницькі характеристики | |
| DI | 12xDI |
| COM | 1x TCL3 |
- Ціна: Ціну уточнюйте