CP-2000 - процесор, Ethernet, RS232, 4 AI/AO, 3 DI 230VAC, 2 DO, CIB

CP-2000 is a basic module of the second generation, which is mainly equipped with:     Two CIB Common Installation Bus® masters with full power supply so that up to 64 sensor and actuator modules for this two-wire bus can be connected directly     Additional CIB branches are added by new generation external masters connected via LAN (ethernet).     TCL2 system expansion bus master. It is equipped with a total of 9 I / Os:     four multipurpose inputs, each of which can be used either as analog or as binary     one input for monitoring the presence of the 230 V AC mains supply     two binary inputs at voltage level 230V AC for HDO monitoring (mass remote control)     two separate relay outputs. Communication capabilities of the basic module CP-2000:     2x Ethernet interface 100 Mbit / s, each with up to 32 simultaneous connections (programming and general IP communication)     USB micro (programming)     USB A for Flash memory, WiFi adapter (client and AP - Access point) etc.     Variant with built-in LTE modem for direct wireless connection to the Internet via a mobile network operator     Slots for up to 4 optional serial interfaces RS-485, RS-232 24 V DC power supply, possibility of direct connection of a backup battery for uninterrupted operation in case of 230 V AC mains failures. CP-2000 is equipped with a new powerful central unit (CPU series L) with memory     1 MB for user program,     128 MB internal disk for storing files with parallel access from the LAN as a network disk,     16MB fast RAM disk     microSD card slot up to 1 TB     File management is provided by a journaling file system     Local communication with the user via OLED display (4 lines / graphic) and 6-key keyboard

DI	3x DI (230 V AC)
DI/AI	4x DI/AI
DO	2x RO
AI
AO
COM	2x ETH 10/100 1x RS-232 4x Serial channel (2x free slot) 1x USB device 1x USB host 1x TCL2 master 2x CIB master
SENSOR

System parameters of the central unit
Row of central unit	I
User program memory	1 MB
Memory for user variables / including RETAIN variables	320 kB/48 kB
Instruction length	4 Byte
Backup of program source code in PLC	Yes, optional in Mosaic
On-line program change in PLC	Yes, including I / O configuration change
DataBox - additional internal data memory	128/257 kB, optional
File system - Internal Drive in PLC	128 MB, journaling file system
File system - RAM disk PLC	16 MB
File System - USB Flash Drive	Supported
File system - Micro SD card	supported (except for variants with WLAN1)
Optional memory card slot	microSD - Card Slot (<= 1TB)
Cycle time per 1k of logic instructions	0,036 ms
Cycle time for 1k integer operations	0,044 ms
Cycle time for 1k floating point operations	0,043 ms
Development environment	Mosaic v2018.2 or higher
Programming languages	ST, IL, LD, FBD, SFC, CFC
RTC - Real time circuit	No
RTC - Backup time	typ. 500 hours
Integrated Web server	Yes
Integrated Datalogger	Yes
Access to PLC variables via web API	Yes
COM - Communication - IP/Ethernet
Ethernet 10/100 Mb (ETHx)	2
WLAN1 (internal, optional)	1
WLAN2 (external via USB host, optional)	1
LTE interface (LTEx, optional)	1
Available system modes on ETH and WLAN	UNI, PC, PLC, PLD
Available system modes on LTE	UNI - Exchange over UDP, TCP and support SSL / TLS encryption PC - EPSNET UDP / EPSNET TCP
TCP / IP protocol	Yes
UDP protocol	Yes
HTTPS protocol	Yes
HTTP protocol	Yes
WebSocket protocol	Yes
Protocol MODBUS/TCP	Yes
SMTP protocol	Yes
IEC 60870-5-104 protocol	Yes
REST API	Yes
COM - USB
USB devices interface	1x micro-USB
USB host interface	1x USB-A
Available system modes on USB	PC
COM - System buses
TCL2 - system I/O bus	1x TCL2 master
TCL2 - Range of one branch of the system I/O bus	10 I / O modules + 4 operator panels + 6 serial channels
CIB - Common Installation Bus (R): Installation I/O bus	2x CIB master (2x 1 A)
CIB - Address range of one branch of the installation bus	32 CFox I/O modules
DI - Parameters of binary inputs DC (group A)
Parameters valid for inputs on the terminals	AI0/DI0 - AI3/DI3
Number of inputs in group	4
Common wire	AGND - module ground
Combined input type	DI/AI Active, for sensing potential-free contacts and measuring resistance sensors
Galvanic isolation of inputs from internal/peripheral circuits	No
Input voltage for log. 1	1 V DC max.
Input current at log. 1 (typ.)	-1,7 mA
The minimum width of the captured pulse	1 ms
Notice	Note that the GND terminals in the 24 V DC and ANALOG OUTPUTS arrays they are connected inside the system. It is not desirable to connect the GND terminal in the ANALOG field OUTPUTS with a negative pole power supply system also inputs as it would cross the other the GND terminal has closed the loop and thereby potentially induced interfering signals.
DI - Parameters of binary AC inputs
Parameters valid for AC inputs on the terminals	IN230V, HDO0, HDO1
Total number of binary AC inputs	3
Number of groups of AC inputs	2
Organization of binary inputs into groups	1x (IN230V), 2x (HDO1, HDO2)
Common wire	L
Input type	230 V AC
Galvanic isolation of internal circuits	Yes
Input voltage for log. 1	230 V AC typ., 200 V AC min., 250 V AC max.
Input current at log. 1 (typ.)	5 mA typ.
RO - Parameters of binary relay outputs (group A)
Parameters valid for the terminals	DO0–DO5, DO7–DO10
Number of relay outputs	2
Organization of relay outputs into groups	1x (DO0) +1x (DO2)
Output type	electromechanical relay, unprotected output
Contact type	NO - Normally Open
Galvanic separation from internal circuits	Yes
Galvanic isolation between groups	Yes
Switching current	16 A max. NO/10 A max NC, 100 mA min.
Switching voltage	250 V AC max., 5 V AC min., 30V DC max.
Short-term output overload - inrush	80 A max. (20 ms max.)
Contact closing time	typ. 15 ms
Contact opening time	typ. 5ms
Limit values of switched resistive load	max. 16A at 30 V DC or 230 V AC
Mechanical life	min. 20 000 000 cycles
Electrical life at maximum resistive load	min. 100,000 cycles
Short-circuit protection	No
Treatment of inductive load	External RC element, varistor (AC), diode (DC)
Insulation voltage between outputs and internal circuits	3750 V AC
Isolation voltage between groups of outputs to each other	3750 V AC
AI - Organization of analog inputs
Total number of analog inputs	4
Number of analog input groups	1
Organization of analog inputs into groups	4x (AI0/DI0-AI3/DI3)
Input type	With common clamp
Common wire	Minus
Galvanic separation from internal circuits	No
External power supply	No
Digital resolution	12 bit
Converter type	Approximation
conversion time	20 μs
Operating modes	periodic input sensing
Insulation potential	500 V DC between input and internal circuits
AI - Analog Input Ranges (Group A)
Parameters valid for inputs on the terminals	AI0/DI0 - AI3/DI3
Passive sensor	NTC Thermistor 20k / 25 °C (-40 to + 125 °C)
DI: Voltage-free contact	0 when> 1.5 kOhm, 1 when <0.5 kOhm
Input impedance in signal range RTD	> 4 kΩ
Resistance measurement error - maximum error at 25 ° C	± 0.5% of full scale
Detection of disconnected sensor	yes, in status word, range overflow
Power supply
Supply voltage, tolerances	24 V DC, +25%, -15%, SELV
Supply voltage when backing up with an external battery	27 V DC, +10%, –15%, SELV
Maximum power input	75 W
Internal protection	Yes, PTC reversible fuse
CIB branch power supply - parameters of the built-in master	2x 1 A/ 24-27 V DC
Power supply from ETH, passive PoE - input (appliance)	ETH1/Power In
Power supply from ETH, passive PoE - output (source)	ETH2 / Power out, jumper configuration
Power supply from ETH, passive PoE - injector parameters	24 V DC, 1A
Possibility of backing up the power supply of the basic module and CIB	Yes, by battery 2x 12 V DC, 1x 24 V DC
Battery parameters	24 V (2x 12V), max. 18 Ah
Size and weight
Weight approx.	300 g
Product dimensions (width x height x depth)	158 x 90 x 62 mm
Module width in multiples of M (17.5 mm)	9M
Operating conditions, product standards
Product standard	ČSN EN 61131-2:2008 (idt IEC 61131-2:2007) - Programmable control units
Protection class of electrical object	II, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016)
IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989)	IP20
Operating areas	Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005)
Degree of pollution	1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007)
Overvoltage category installation	II, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007)
Type of device	Module on DIN rail
Working position	Vertical
Type of operation (operating frequency)	Continuous
Ambient operating temperatures	-20 °C to + 55 °C
Operating temperature maximum (° C)	+55°C
Operating temperature minimum (° C)	-20°C
Operating relative humidity	from 10 % up to 95 % without condensation
Operating atmospheric pressure	min. 70 kPa (<3,000 m above sea level)
Storage temperatures	–25 °C to +70 °C
Electromagnetic compatibility, Mechanical endurance
Electromagnetic compatibility / Emission	B, according to EN 55032 ed. 2: 2017 (idt CISPR 32: 2015)
Emmisions - note	In premises where the use of radio and television receivers can be expected to be used a distance of 10 m from these devices may cause radio interference. In such a case, the user may be required to take appropriate action.
Electromagnetic compatibility / Immunity	min. as required by EN 61131-2: 2007
Sinusoidal vibration endurance	10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.)
Packaginng, transportation, storage
Description	The module is packed in a paper box according to the internal packing instructions. The package includes the following documentation. The outer packaging is carried out according to the scope of the order and the method of transport to the transport a package bearing the transport labels and other particulars necessary for transport. Transport from the manufacturer is carried out in the manner agreed upon when ordering. Product transport the customer's own means must be carried out by covered means of transport, in the specified position label on the packaging. The box must be stowed so as to prevent spontaneous movement a damage to the outer packaging. The product must not be exposed to direct weathering during transport and storage influences. Transport is allowed at temperatures from -25 ° C to +70 ° C, relative humidity 10% up to 95% (non-condensing) and a minimum atmospheric pressure of more than 70 kPa. Storage of the product is only allowed in clean rooms without conductive dust, aggressive gases and vapors. The most suitable storage temperature is 20 ° C
Installation
Assembly description	The basic module is mounted vertically on the U-rail ČSN EN 50022. The installation of the assembly (basic module and peripheral modules, if applicable) is performed according to TXV 004 50.
Exchangeable submodules	The optional MR-013x submodules of the serial interface are mounted in the base module CP-2007 on the bottom plate, which is accessible after removing the bottom of the housing. We only handle the module without power supply!
Connection
Warnings / Cautions	If you do not use a backup battery, connect terminals C1 and C4 with a wire!
Connection of power and system communication	connector with 2.5 mm2 screw terminal
Connection of inputs / outputs	connector with screw terminal 2.5 mm2
Ethernet	RJ-45
Serial channels	screw-type connector 9x 1.5 mm2
USB device connection	type micro B
USB host connection	type A
Module operation
Module configuration	The module is operated, set and diagnosed from the MOSAIC programming environment. It is also possible to connect to the PLC using a web browser on port 8080. If the PLC has an IP address set eg 192.168.134.178 (default address on port ETH1, port ETH2 has DHCP enabled), just enter the address in the form http://192.168.134.178:8080 and the web browser displays the PLC configuration pages.
Commissioning	The module is ready for operation after connection of the supply voltage. The MODE button is available on the module panel to display the currently set IP address of the Ethernet interface. Parameters of all interfaces are set in the Mosaic programming environment. The exact setup procedure is given in the TXV 004 50 documentation.
Module diagnostics	The basic diagnostic system of the module is part of its standard software. It operates from module power on and operates independently of the user. Diagnostic error states of the module and connected peripheral modules of the assembly are signaled on the module display and are available for processing by the master system. For more information, see TXV 004 50.
Maintenance
Description	The module does not require any maintenance under general installation conditions.
Notice	Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!!
Warranty
Generally	Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s.
Notice	You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change.