CP-1013 Процесор з LCD 4×20, Ethernet, RS232, 8×AI/DI, 4×DI/HSC, 4×AO, 7×RO, 4×DO
Знято з виробництва
- Під замовлення
- Код: TXN 110 13
Відправка з 03 жовтня 2026Ціну уточнюйте
Мінімальна сума замовлення на сайті — 200 ₴
+380 (98) 363-64-36
повернення товару протягом 14 днів за домовленістю
CP-1013 Процесор з LCD 4×20, Ethernet, RS232, 8×AI/DI, 4×DI/HSC, 4×AO, 7×RO, 4×DO
Ціну уточнюйте
Під замовленняОпис
Характеристики
Інформація для замовлення
⚠️ Товар знято з виробництва
Ця модель більше не випускається виробником і недоступна до замовлення.
Потрібна заміна? Надішліть нам артикул, фото обладнання або технічні характеристики — ми допоможемо підібрати сучасний аналог із сумісними параметрами.
Крім підбору сучасного аналога, для окремих моделей ми також можемо запропонувати діагностику та, за наявності технічної можливості, ремонт або відновлення обладнання.
The basic module CP-1003 is equipped with eight multi-purpose inputs, each of which can be used either as analog (voltage, current or for passive temperature sensors) or as binary 24V, eight fast binary inputs with adjustable decision level four analog outputs ± 10 V, eight relay outputs and four fast transistor outputs with the possibility of direct connection of DC or stepper motors. The CP-1003 basic module is equipped with a central unit (CPU) of the L series, which is designed for applications with performance requirements. It contains backed up CMOS RAM for user programs, data, tables, user registers and DataBox, Flash memory for user backup program, slot for MMC / SD / SDHC memory card, real-time circuit, Ethernet interface, up to 4 serial channels (one with fixed RS-485 interface, another with slot for the optional submodule) and two TCL2 system interfaces for connecting expansion modules that increase the number of I / O systems.
| DI | 8x DI/HSC |
| DI/AI | 8x DI/AI |
| DO | |
| AI | |
| AO | 4x AO |
| COM | 1x ETH 10/100 1 × RS-485 1-3x Serial channel (1x free slot) 2 × TCL2 master |
| SENSOR |
| System parameters of the central unit | |
|---|---|
| Row of central unit | K |
| User program memory | 192 + 64 kB |
| Memory for user variables / including RETAIN variables | 64 kB/32 kB |
| Instruction length | 2 ÷ 10 bytes |
| Backup of program source code in PLC | Yes, in program backup memory (EEPROM) |
| On-line program change in PLC | Yes, including I / O configuration change |
| Memory for project archiving - internal | 2 MB |
| DataBox - additional internal data memory | 512 kB |
| Optional memory card slot | SD - Card Slot |
| Cycle time per 1k of logic instructions | 0,2 ms |
| Development environment | Mosaic |
| Programming languages | ST, IL, LD, FBD, SFC, CFC |
| RTC - Real time circuit | No |
| RAM and RTC backup 1) without / with backup battery | type. 500 hr / typ. 20,000 hours |
| Integrated Web server | Yes |
| Integrated Datalogger | Yes |
| Access to PLC variables via web API | Yes |
| Notice | 1) Applies to the basic module without power supply, the backup circuits are disconnected when the power supply is switched on 2) The serial interface CH1 is permanently equipped with an RS-485 interface. The serial interface type CH2 to CH4 is selectable via interchangeable submodules |
| COM - Communication - IP/Ethernet | |
| Ethernet 10/100 Mb (ETHx) | 1 |
| Available system modes on ETH and WLAN | UNI, PC, PLC, PLD |
| TCP / IP protocol | Yes |
| UDP protocol | No |
| HTTP protocol | No |
| WebSocket protocol | No |
| Protocol MODBUS/TCP | No |
| SMTP protocol | No |
| IEC 60870-5-104 protocol | No |
| REST API | No |
| COM - Serial channels | |
| max. number of optional serial channels in the basic module | 4 |
| max. number of expanding serial channels on the TCL2 bus | 6 |
| Number of internal RS-232 serial channels | 1 |
| Available system modes on CH5-10 | UNI, CSJ (CAN) |
| Modbus RTU / ASCII master protocol | No |
| Modbus protocol RTU/ASCII slave | No |
| Profibus DP master protocol (<180 kbit/s) | No |
| COM - System buses | |
| TCL2 - system I/O bus | 1x TCL2 master |
| TCL2 - Range of one branch of the system I/O bus | 10 I / O modules + 4 operator panels + 6 serial channels |
| The communication rate of the system I / O bus | 345 kbps |
| System I / O bus terminating resistor | 120 Ω |
| CIB - Common Installation Bus (R): Installation I/O bus | 1x CIB master (100 mA) |
| CIB - Address range of one branch of the installation bus | 32 CFox I/O modules |
| DI - Parameters of binary inputs DC (group A) | |
| Common wire | minus |
| Input type | Type 1 (IEC) |
| Galvanic isolation of inputs from internal/peripheral circuits | No |
| Diagnostics | indication of energized input by LED on module panel |
| Input voltage for log. 0 | 0 V DC; -5 V DC min.; +5 V DC max. |
| Input voltage for log. 1 | 24 V DC; 15 V DC min.; 30 V DC max. |
| Input current at log. 1 (typ.) | 5 mA typ. |
| Delay from log. 0 to log. 1 | 5 μs |
| Delay from log. 1 to log. 0 | 5 μs |
| The minimum width of the captured pulse | 50 μs |
| Notice | Note that GND terminals in 24 V DC and DIGITAL / SPECIAL INPUTS they are connected inside the system. It is not desirable to connect the GND terminal in the DIGITAL / SPECIAL INPUTS with negative pole power supply system also inputs because it would over the second GND terminal closed the loop and thereby potentially induced interfering signals. |
| HSC - Special functions of binary inputs / counters | |
| Unidirectional counter (UP) | 2x (DI0); (DI2) |
| Two unidirectional counters (UP / UPB) | 2x (DI0/DI2); (DI2/DI3) |
| Bidirectional counter (UP/DOWN) | 2x (DI0/DI1); (DI2/DI3) |
| Counter with direction control (CLK/DIR) | 2x (DI0/DI1); (DI2/DI3) |
| Bi-directional counter with reset and intercept (UP / DOWN / CLR / CAP) | 1x (DI0/DI1/DI2/DI3) |
| Counter with direction control with reset and latch (CLK / DIR / CLR / CAP) | 1x (DI0/DI1/DI2/DI3) |
| IRC Basic (V/G) | 2x (DI0/DI1); (DI2/DI3) |
| IRC with Zero and Capture (V / G / NI / MD) | 1x (DI0/DI1/DI2/DI3) |
| Measure the pulse length | 4x (DI0,DI1, DI2, DI3) |
| Period measurement | 4x (DI0,DI1, DI2, DI3) |
| RO - Parameters of binary relay outputs (group A) | |
| Parameters valid for the terminals | DO0-DO5 |
| Number of relay outputs | 6 |
| Number of output groups | 2 |
| Number of outputs in group | 3 |
| Diagnose | Alarm signaling on panel module |
| Switching current | 3 A max., 100 mA min. |
| Switching voltage | 250 V AC max., 5 V AC min., 30V DC max. |
| Short-term output overload - inrush | 4 A max. |
| Current through common clamp | 10 A max. |
| Contact closing time | typ. 10 ms |
| Contact opening time | typ. 4 ms |
| Limit values of switched resistive load | max. 3A at 30 V DC or 230 V AC |
| Switching inductive load limits DC13 | max. 3 A at 30 V DC |
| Switching inductive load limits AC15 | max. 3 A at 230 V AC |
| Switching frequency without load | max. 300 switching / min. |
| Switching frequency with rated load | max. 20 switching / min. |
| Mechanical life | min. 5,000,000 cycles |
| Electrical life at maximum resistive load | min. 100,000 cycles |
| Electrical life at maximum load inductive DC13 | min. 100,000 cycles |
| Electrical life at maximum load inductive AC15 | min. 100,000 cycles |
| Short-circuit protection | No |
| Treatment of inductive load | External RC element, varistor (AC), diode (DC) |
| Insulation voltage between outputs and internal circuits | 3750 V AC |
| Isolation voltage between groups of outputs to each other | 3750 V AC |
| AI - Organization of analog inputs | |
| Total number of analog inputs | 4 |
| Number of inputs per group | 4 |
| Number of analog input groups | 1 |
| Organization of analog inputs into groups | 4x (DI4/AI0-DI7/AI3) |
| Input type | With common clamp |
| Common wire | Minus |
| Galvanic separation from internal circuits | No |
| Diagnostics | overload signaling in status word |
| Converter type | Approximation |
| conversion time | 20 μs |
| Operating modes | periodic input sensing |
| AI - Analog Input Ranges (Group A) | |
| Voltage | 0 to 10 V / 2,579 mV |
| Voltage input error - repeatability under steady state conditions | 0.05% of full scale |
| Permissible continuous overload - voltage input | -20 V to +30 V |
| Open input detection | No |
| Power supply | |
| Nominal supply voltage (V) | 24 V DC |
| Supply voltage, tolerances | 24 V DC, +25%, -15%, SELV |
| Supply voltage when backing up with an external battery | 27 V DC, +10%, –15%, SELV |
| Typical power input | 5 W |
| Maximum power input | 8 W |
| Module thermal/power loss | 6 W |
| Maximum current consumption (mA) | 400 mA |
| Galvanic separation of power supply from internal circuits | No |
| Internal protection | Yes, PTC reversible fuse |
| Description of power supply | Difference between typical and maximum power input is given by possible load of CIB buses and number of switched outputs and CPU load |
| CIB branch power supply - parameters of the built-in master | 1x 100 mA/ 24 V DC |
| Size and weight | |
| Weight approx. | 200 g |
| Product dimensions (width x height x depth) | 105 x 92 x 63 mm |
| Module width in multiples of M (17.5 mm) | 6M |
| Module width | 105 mm |
| Module height | 92 mm |
| Module depth | 63 mm |
| Operating conditions, product standards | |
| Product standard | ČSN EN 61131-2: 2005 (idt IEC61131-2: 2003) - Programmable control units |
| Protection class of electrical object | II, according to ČSN EN 61140: 2003 (idt IEC 61140: 2001) |
| IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989) | IP20 |
| Operating areas | Normal, according to ČSN 33 2000-3: 1995 (mod IEC 364-3: 1993) |
| Degree of pollution | 1, according to ČSN EN 60664-1: 2004 (mod IEC 60664-1: 1992) |
| Overvoltage category installation | II, acc. ČSN EN 60664-1:2004 (mod IEC 606641:1992) |
| Type of device | Module on DIN rail |
| Working position | Vertical |
| Type of operation (operating frequency) | Continuous |
| Ambient operating temperatures | -20 °C to + 55 °C |
| Operating relative humidity | from 10 % up to 95 % without condensation |
| Operating atmospheric pressure | min. 70 kPa (<3,000 m above sea level) |
| Storage temperatures | –25 °C to +70 °C |
| Electromagnetic compatibility, Mechanical endurance | |
| Electromagnetic compatibility / Emission | A, according to EN 55022: 1999 (mod CISPR22: 1997) |
| Emmisions - note | In premises where the use of radio and television receivers can be expected to be used a distance of 10 m from these devices may cause radio interference. In such a case, the user may be required to take appropriate action. |
| Electromagnetic compatibility / Immunity | min. as required by EN 61131-2: 2007 |
| Sinusoidal vibration endurance | 10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.) |
| Packaginng, transportation, storage | |
| Description | The module is packed in a paper box according to the internal packing instructions. This documentation is also part of the package. The outer packaging is carried out according to the scope of the order and the method of transport in a transport package provided with transport labels and other data necessary for transport. Transport from the manufacturer is carried out in the manner agreed upon when ordering. The transport of the product by the customer's own means must be carried out by covered means of transport, in the position specified by the label on the packaging. The box must be stored in such a way that it does not move spontaneously and the outer packaging is not damaged. The product must not be exposed to direct weather conditions during transport and storage. Transport is permitted at temperatures of -25 ° C to +70 ° C, relative humidity of 10% to 95% (non-condensing) and a minimum atmospheric pressure higher than 70 kPa. The product may only be stored in clean rooms free of conductive dust, aggressive gases and vapors. The most suitable storage temperature is 20 ° C. |
| Installation | |
| Assembly description | The basic module is mounted vertically on the U-rail ČSN EN 50022. Installation of the assembly (basic module and peripheral modules, if any) is carried out according to TXV 004 10. |
| Exchangeable submodules | The optional MR-01xx serial interface submodules are fitted to the CP-1004 basic module on the center plate to the position indicated in Fig. 7.1. If necessary, the installation or replacement of a submodule with a serial channel interface is required Use a screwdriver to release the latches on the bottom of the housing. After removing the lower part of the case, remove it the board assembly from the rest of the housing (by gently pressing the inner board assembly downward on the Slide the Ethernet connector down). After removing the top plate with indication and connector The Ethernet interface is a replaceable submodule accessible. After installing the submodule boards carefully insert into each other - be careful not to bend the tips and the following incorrect insertion. Then assembled Carefully slide the plate assembly into the cover. Pay attention to the risk of bending the LEDs and correct alignment button and ETHERNET connector. After insertion into the cover snap the bottom of the module. |
| Module operation | |
| Module configuration | The module is operated, set up and diagnosed from the Mosaic development environment. |
| Commissioning | The module is ready for operation after connection of the supply voltage. The module panel is available MODE button to display the currently set Ethernet IP address. Parameters of all interfaces are set in the Mosaic programming environment. The exact setting procedure is shown in TXV 004 documentation 10. Other activities (programming, application debugging, etc.) are performed in the MOSAIC development environment. |
| Module diagnostics | The basic diagnostic system of the module is a part of its standard software. It operates from module power on and operates independently of the user. Diagnostic error the status of the module and the connected peripheral modules of the assembly are indicated on the module display and are available for processing by the master system. For more information see TXV 004 10. |
| Maintenance | |
| Description | The module does not require any maintenance under general installation conditions. The operations in which a part of the module has to be dismantled must always be carried out with the supply voltage disconnected. |
| Warning | Since the module contains semiconductor components, it is necessary to observe the rules for working with electrostatically sensitive components when handling the removed cover. It is not allowed to touch the printed circuits directly without protective measures. |
| Additional backup battery - maintenance | If you need to extend the backup time (more than 500 hours) it is necessary to fit an additional backup lithium battery type CR2032, 3 V, diameter 20 mm, thickness 3.2 mm in the holder located on the middle plate of the module assembly (dismantling the assembly is described in chapter 7). ). When mounting or. Replace the battery so that it is not short-circuited! We recommend replacing the battery after 2 to 3 years. Unnecessary batteries must be handed over to authorized organizations for disposal. |
| Warranty | |
| Warning | Before turning on the system, all the conditions of this documentation must be met, otherwise the protection provided by the equipment may be impaired. The system may not be escorted unless it has been verified and confirmed that the machinery incorporating the Foxtrot system meets the requirements of Directive 89/392 / CEE where applicable. All repairs and servicing of the product are performed exclusively by the manufacturer or by an authorized person. The system installer is responsible for the safety of the system. |
| Основні | |
|---|---|
| Виробник | Teco |
| Країна виробник | Чехія |
| Стан | Новий |
| Користувальницькі характеристики | |
| DI | 8x DI/HSC |
| DI/AI | 8x DI/AI |
| AO | 4x AO |
| COM | 1x ETH 10/100 1 × RS-485 1-3x Serial channel (1x free slot) 2 × TCL2 master |
- Ціна: Ціну уточнюйте