C-DL-2064M Шлюз CIB–DALI для 64 пристроїв DALI-2
- Під замовлення
- Код: TXN 143 32
Відправка з 10 жовтня 2026Ціну уточнюйте
Мінімальна сума замовлення на сайті — 200 ₴
+380 (98) 363-64-36
повернення товару протягом 14 днів за домовленістю
C-DL-2064M Шлюз CIB–DALI для 64 пристроїв DALI-2
Ціну уточнюйте
Під замовленняОпис
Характеристики
Інформація для замовлення
The module C‑DL‑2064M(Order No.: TXN 143 32) is a converter of protocols CIB‑DALI. It is intended for lighting systems with DALI protocol specification NEMA Standards Publication 243‑2004 Digital Addressable Lighting Interface (DALI) Control Devices Protocol PART 2‑2004 . From version FW v.1.5 module can be used as a protocol converter CIB‑DSI. Signals of CIB and DALI/DSI buses are connected to screw terminals. The internal circuits of the module are powered from the CIB bus. The output circuits of the DALI/DSI bus are powered by an external 24 V DC source. Program control functions of module is supported by function blocks from the DaliLib.mlb library.
| DI | |
| DI/AI | |
| DO | |
| AI | |
| AO | |
| COM | 1x CIB 1x DALI/DSI |
| SENSOR |
| COM - System buses | |
|---|---|
| CIB - Common Installation Bus (R): Installation I/O bus | 1x CIB slave |
| DI - Organization of binary inputs | |
| Total number of binary inputs | 1 |
| Number of groups of binary inputs | 1 |
| DI - Parameters of binary inputs DC | |
| Number of inputs in group | 1 |
| Common wire | GND - module ground |
| Galvanic separation of inputs from CIB bus | No |
| AI - Organization of analog inputs | |
| Total number of analog inputs | 1 |
| Number of inputs per group | 1 |
| Input type | AI / DI - combined |
| Common wire | GND terminal |
| Galvanic separation from internal circuits | No |
| AI - Analog Input Ranges | |
| Passive sensor | NTC Thermistor 12k / 25 °C (-40 to + 125 °C) |
| Measurement of supply network parameters - frequency | |
| Nominal frequency | 50/60 Hz |
| Frequency range | 45 - 65 Hz |
| Measurement of supply network parameters - voltage | |
| Rated voltage UNOM (UDIN) | 180–250VAC |
| Crest factor in UNOM | 2 |
| Measuring range, phase voltage (UL-N) | 20÷450 V AC |
| Voltage measurement accuracy | ± 10% of value or ± 1% of range |
| Measurement category | 300V CAT II |
| Input impedance | 0,7 MΩ |
| Input consumption | max. 0,09 VA |
| Permanent overload (UL-N) | 1000 V AC |
| Peak overload, for 1 s (UL-N) | 1300 V AC |
| Measurement of supply network parameters - currents | |
| Method for measuring current | indirect via current transformer |
| Nominal current of transformer Inom | N * 0,05 A AC, max 65 A AC |
| Crest factor at Inom | 1,8 |
| Current measurement accuracy | ±10% of value or ±1% of range |
| Input impedance | 3 Ω |
| Input consumption | max. 8 mVA |
| Permanent overload | 0,25 A AC |
| Peak overload, for 5 s, repetition period min. 60 s | 0,36 A AC |
| Measurement of supply network parameters - other quantities | |
| Active power, measuring range (PNOM = UNOM × INOM×cosφ); [W, V, A] | limited by measured voltage and current ranges |
| Reactive power, measuring range (QNOM = UNOM × INOM×sinφ); [VA, V, A] | limited by measured voltage and current ranges |
| Accuracy of active or reactive power (A) | ±10% of value or ±1% of range |
| Power supply | |
| Supply voltage, tolerances | 24/27 V DC from CIB bus |
| Power supply from CIB - typical current consumption (mA) | 16 mA |
| Internal protection | No |
| Size and weight | |
| Weight approx. | 53 g (65 g of double-sided proud transformative transformer) |
| Product dimensions (width x height x depth) | 23 x 90 x 58 mm |
| Module width in multiples of M (17.5 mm) | 1,5M |
| Operating conditions, product standards | |
| Product standard | ČSN EN 61131-2:2008 (idt IEC 61131-2:2007) - Programmable control units |
| Protection class of electrical object | II, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016) |
| IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989) | IP20 |
| Operating areas | Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005) |
| Degree of pollution | 2, according to ČSN EN 60664-1 ed.2: 2008 (idt IEC 60664-1: 2007) |
| Overvoltage category installation | II, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007) |
| Type of device | Module on DIN rail |
| Working position | Vertical |
| Type of operation (operating frequency) | Continuous |
| Ambient operating temperatures | -20 °C to + 55 °C |
| Operating relative humidity | from 10 % up to 95 % without condensation |
| Operating atmospheric pressure | min. 70 kPa (<3,000 m above sea level) |
| Storage temperatures | –25 °C to +70 °C |
| Electromagnetic compatibility, Mechanical endurance | |
| Electromagnetic compatibility / Emission | A, according to EN 55032 ed. 2: 2017 (idt CISPR 32: 2015) |
| Electromagnetic compatibility / Immunity | min. according to ČSN EN 60730-1 ed.3: 2012 |
| Sinusoidal vibration endurance | 10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.) |
| Packaginng, transportation, storage | |
| Description | The module is packed in a cardboard box. The product must not be exposed to direct weather conditions during transport and storage. The product must only be stored in clean rooms free from conductive dust, aggressive gases and vapours. The most suitable storage temperature is 20 °C. |
| Installation | |
| Assembly description | The module is mounted in a vertical position on the U-rail ČSN EN 50022. Installation of the assembly (basic module and possibly peripheral modules) is performed according to TXV 004 13. |
| Connection | |
| Connection description | The module is connected via screw terminals. The measured voltage is connected to terminal U via a suitable fuse with characteristics according to the environment (e.g. a fuse with a value of 0.05 A) and the neutral conductor to terminal N. To connect the current measurement, it is necessary to use a measuring current transformer with such a conversion ratio that the output current in the required measurement range is up to 0.05A AC and with the corresponding insulation voltage, or the transformer must be installed on an insulated primary conductor with the corresponding insulation voltage. The secondary winding of the transformer is connected to terminals S1 and S2. The CIB bus is connected to terminals CIB+ and CIB–. |
| Connection of power and system communication | terminal block with screw terminal 0,2 - 2,5 mm² |
| Connection of inputs / outputs | terminal block with screw terminal 0,2 - 2,5 mm2 |
| Module operation | |
| Commissioning | The module is operated, set up and diagnosed from the MOSAIC programming environment or other parameterization software. The module is ready for operation after connecting the supply voltage and the CIB bus. The HW address is indicated on the label on the module. Attention: When working with the module, it is necessary to observe all necessary measures to protect people and property from injury and damage by electric current! The module must be operated by a person with the prescribed qualifications for such activity and this person must be thoroughly familiar with the principles of working with the module. If the module is connected to parts that are under dangerous voltage, it is necessary to observe all necessary measures to protect users and equipment from electric shock. The worker performing installation and/or maintenance of the device must be equipped with and use personal protective equipment and other safety equipment during work. If the module is used in a manner not specified by the manufacturer, the protection provided by the module may be reduced. Further information can be found in the manual Peripheral modules on the CIB bus, order no.: TXV 004 13.01. |
| Module diagnostics | Basic diagnostics are performed internally and the measurement results are available in the relevant registers of the Mosaic environment. The module status is indicated by the green RUN LED located on the front panel below the CIB bus connection terminals. After the CIB bus is connected, the green RUN LED lights up, indicating the presence of supply voltage on the CIB interface. After the module has established communication with the central unit, the RUN LED flashes. This means that the module is ready for operation. |
| Maintenance | |
| Description | The module does not require any maintenance under general installation conditions. The operations in which a part of the module has to be dismantled must always be carried out with the supply voltage disconnected. |
| Notice | Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!! |
| Warranty | |
| Generally | Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s. |
| Notice | You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change. |
| Основні атрибути | |
|---|---|
| Виробник | Teco |
| Країна виробник | Чехія |
| Стан | Новий |
| Користувальницькі характеристики | |
| COM | 1x CIB 1x DALI/DSI |
- Ціна: Ціну уточнюйте