C-EM-0100M Однофазний лічильник електроенергії CIB, 230 VAC
- Під замовлення
- Код: TXN 143 40
Відправка з 10 жовтня 2026Ціну уточнюйте
Мінімальна сума замовлення на сайті — 200 ₴
+380 (98) 363-64-36
повернення товару протягом 14 днів за домовленістю
C-EM-0100M Однофазний лічильник електроенергії CIB, 230 VAC
Ціну уточнюйте
Під замовленняОпис
Характеристики
Інформація для замовлення
Module of a 1-phase 4-quadrant electricity meter providing all parameters of consumed and supplied energy. The measurement is indirect, the current is sensed by a current transformer according to the required input range. The data is transmitted via a two-wire CIB - Common Installation Bus®
| DI | |
| DI/AI | 1x DI/AI |
| DO | |
| AI | |
| AO | |
| COM | 1x CIB slave |
| SENSOR |
| COM - System buses | |
|---|---|
| CIB - Common Installation Bus (R): Installation I/O bus | 1x CIB slave |
| DI - Organization of binary inputs | |
| Total number of binary inputs | 5 |
| Number of groups of binary inputs | 2 |
| Organization of binary inputs into groups | 4x DI (DI/AI1 - DI/AI4) 1x DI (DI/AI5) |
| DI - Parameters of binary inputs DC | |
| Parameters valid for inputs on the terminals | DI/AI1 - DI/AI5 |
| Common wire | GND - module ground |
| Combined input type | DI/AI Active, for sensing potential-free contacts and measuring resistance sensors |
| Galvanic isolation of inputs from internal/peripheral circuits | No |
| Galvanic separation of inputs from CIB bus | No |
| Internal input resistance | 2 kΩ |
| Max. resistance for closed contact, log. 1 | < 0,5 kΩ |
| Min. resistance for open contact, log. 0 | ≥ 2,7 kΩ |
| Balanced resistance input | 2× 1k1 (tamper/0/1/tamper) |
| AI - Organization of analog inputs | |
| Total number of analog inputs | 5 |
| Number of analog input groups | 2 |
| Organization of analog inputs into groups | 4x DI (DI/AI1 - DI/AI4) 1x DI (DI/AI5) |
| Input type | 4x DI (DI/AI1 - DI/AI4) 1x DI (DI/AI5) |
| Common wire | GND terminal |
| Galvanic separation from internal circuits | No |
| Galvanic isolation of the inputs from each other | No |
| AI - Analog Input Ranges | |
| Passive sensor | NTC Thermistor 12k / 25 °C (-40 to + 125 °C) |
| Input impedance in signal range RTD | 2,0 kΩ |
| Resistance measurement error - maximum error at 25 ° C | ±0.5% of full scale, ±2% of value |
| AO - Analog output parameters | |
| The number of groups of analogue outputs | 1 |
| Number of outputs in group | 4 |
| Number of outputs and their organization into groups | 4x AO (AO1-AO4) |
| Common wire of group | GND terminal |
| Galvanic isolation from internal circuits | No |
| Output type | active voltage output |
| Voltage output - voltage | 0 - 10 V |
| Voltage output - Resolution 1 LSB | 10,546 mV |
| Voltage output - Adjustable range | 0 ÷ 125 % Ujm |
| Voltage output - Load resistance | >1 kΩ |
| Voltage output - Load capacity | 250 nF |
| Voltage output - maximum output current | 10 mA |
| Voltage output - Maximum output current for the group | 15 mA |
| Power supply | |
| Supply voltage, tolerances | 24/27 V DC from CIB bus |
| Power supply from CIB - maximum current consumption (mA) | 42 mA |
| Size and weight | |
| Weight approx. | 60 g |
| Product dimensions (width x height x depth) | 35 × 92 × 42 mm |
| Operating conditions, product standards | |
| Product standard | ČSN EN 60730-1 ed.4 :2017 (EN 60730-1:2016) -Automatic electronic control device (for household and similar purposes) |
| Protection class of electrical object | III, according to ČSN EN 61140 ed.3: 2016 (idt IEC 61140:2016) |
| IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989) | IP20 |
| Operating areas | Normal, acc. ČSN 33 2000-1 ed.2: 2009 (mod IEC 60354-1:2005) |
| Degree of pollution | 1, according to ČSN EN 60664-1 ed.2:2008 ( idt IEC 60664-1:2007) |
| Overvoltage category installation | II, according to EN 60664-1 ed_2: 2008 (idt IEC 60641-1: 2007) |
| Type of device | Module on DIN rail |
| Working position | Any |
| Type of operation (operating frequency) | Continuous |
| Ambient operating temperatures | 0 ° C to + 70 ° C |
| Operating relative humidity | from 10 % up to 95 % without condensation |
| Operating atmospheric pressure | min. 70 kPa (<3,000 m above sea level) |
| Storage temperatures | –25 ° C to + 85 ° C |
| Electromagnetic compatibility, Mechanical endurance | |
| Electromagnetic compatibility / Emission | ČSN EN 55022 ed2:2007 (mod CISPR22:2005) |
| Electromagnetic compatibility / Immunity | min. according to ČSN EN 60730-1 ed.2: 2001 |
| Sinusoidal vibration endurance | 10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.) |
| Packaginng, transportation, storage | |
| Description | Модуль упакован в антистатический пакет. Эта документация также является частью пакета. Внешняя упаковка осуществляется в соответствии с объемом заказа и способом транспортировки в транспортной упаковке, снабженной этикетками и другими данными, необходимыми для транспортировки. Продукт не должен подвергаться воздействию прямых погодных условий во время транспортировки и хранения. Соложение продукта разрешено только в чистых помещениях. без токопроводящей пыли, агрессивных газов и паров. Наиболее подходящая температура хранения - 20 ° C. |
| Connection | |
| Connection of power and system communication | connector with 2.5 mm2 screw terminal |
| Connecting inputs | connector with screw terminal 2.5 mm2 |
| Connecting outputs | connector with screw terminal 1.5 mm2 |
| Module operation | |
| Module configuration | The module is operated, set up and diagnosed from the Mosaic development environment. |
| Commissioning | The module is operated, set and diagnosed from the MOSAIC programming environment or other parameterization software. The module is ready for operation after connecting the supply voltage and the CIB bus. The HW address is indicated on the label on the module. |
| Module diagnostics | The basic diagnostics is performed internally and the result is available in the relevant registers of the Mosaic environment. |
| Maintenance | |
| Description | The module does not require any maintenance under general installation conditions. The operations in which a part of the module has to be dismantled must always be carried out with the supply voltage disconnected. |
| Notice | Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!! |
| Warranty | |
| Generally | Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s. |
| Notice | You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change. |
| Основні | |
|---|---|
| Виробник | Teco |
| Країна виробник | Чехія |
| Стан | Новий |
| Користувальницькі характеристики | |
| DI/AI | 1x DI/AI |
| COM | 1x CIB slave |
- Ціна: Ціну уточнюйте