C-IT-0908S-NPN Модуль CIB, 6×DI, 2×AI/DI, драйвер 8×NPN LED

The C-IT-0908S module is intended for the CIB Common Installaton Bus® for the connection of sensing analog or binary signals (sensing potential-free contacts) and controlling binary outputs, including for driving LEDs. Inputs DI1 to DI6 can only be set as binary. They also work in balanced input mode. Inputs DI / AI7 to DI / AI8 can be set as binary or analog. Input AI9 can only be set as analog. Eight binary outputs are designed to drive LEDs connected in a group with common cathodes or common anodes (version with * .01 number),

DI	6x DI
DI/AI	2x DI/AI
DO	8x DO
AI	1x AI
AO
COM	1x CIB
SENSOR

COM - System buses
CIB - Common Installation Bus (R): Installation I/O bus	1x CIB slave
DI - Organization of binary inputs
Total number of binary inputs	8
Number of groups of binary inputs	2
Organization of binary inputs into groups	6x (DI1 - DI6); 2x (DI/AI7 a DI/AI8)
DI - Parameters of binary inputs DC (group A)
Number of inputs in group	6
Common wire	GND - module ground
Combined input type	DI - Binary, balanced
Galvanic separation of inputs from CIB bus	No
Max. measuring voltage on the connected contact	3,3 V DC
Internal input resistance	2,2 kΩ
Balanced resistance input	2× 1k1 (tamper/0/1/tamper)
DO/RO - Organization of binary outputs
Total number of binary outputs	8
Number of binary output groups	1
DO - Parameters of binary transistor outputs (group A)
Number of transistor outputs	8
Number of output groups	1
Number of outputs in group	8
Output type	PNP open collector (variant with number .01: NPN)
Galvanic separation from internal circuits	No
Switching voltage	27 V DC
Switching current, output load	3mA max.
AI - Organization of analog inputs
Total number of analog inputs	3
Number of analog input groups	2
Organization of analog inputs into groups	(DI/AI7, DI/AI8) + AI9
Input type	With common clamp
Common wire	GND terminal
Galvanic separation from internal circuits	No
Diagnostics	overload signaling in status word
AI - Analog Input Ranges (Group A)
Passive sensor	NTC Thermistor 12k / 25 °C (-40 to + 125 °C)
Resistance measurement error - maximum error at 25 ° C	± 0.5% of full scale
Power supply
Supply voltage, tolerances	24/27 V DC from CIB bus
Power supply from CIB - typical current consumption (mA)	30 mA
Power supply from CIB - maximum current consumption (mA)	65 mA
Power supply from CIB - internal protection	No
Size and weight
Weight approx.	7 g
Module width	55 mm
Module height	26 mm
Module depth	20 mm
Product dimensions (width x height x depth)	55 × 26 × 20 mm
Operating conditions, product standards
Product standard	ČSN EN 60730-1 ed. 2:2001 (mod IEC 60730-1:1999)
Protection class of electrical object	III, according to ČSN EN 61140: 2003 (idt IEC 61140: 2001)
IP rating (Ingress Protection) according to ČSN EN 60529: 1993 (idt IEC 529: 1989)	IP10B
Operating areas	Normal, according to ČSN 33 2000-3: 1995 (mod IEC 364-3: 1993)
Degree of pollution	1, according to ČSN EN 60664-1: 2004 (mod IEC 60664-1: 1992)
Overvoltage category installation	II, acc. ČSN EN 60664-1:2004 (mod IEC 606641:1992)
Type of device	In the installation box, under the cover
Working position	Any
Type of operation (operating frequency)	Continuous
Ambient operating temperatures	0 ° C to + 70 ° C
Operating temperature maximum (° C)	+70°C
Operating temperature minimum (° C)	0°C
Operating relative humidity	from 10 % up to 95 % without condensation
Operating atmospheric pressure	min. 70 kPa (<3,000 m above sea level)
Storage temperatures	–25 ° C to + 85 ° C
Electromagnetic compatibility, Mechanical endurance
Electromagnetic compatibility / Emission	ČSN EN 55022 ed2:2007 (mod CISPR22:2005)
Electromagnetic compatibility / Immunity	min. according to ČSN EN 60730-1 ed.2: 2001
Sinusoidal vibration endurance	10 Hz to 57 Hz, amplitude 0,075 mm, 57 Hz to 150 Hz, acceleration 1 G (Fc test according to EN 60068-2-6: 1997 (idt IEC 68-2-6: 1995), 10 cycles per axis.)
Packaginng, transportation, storage
Description	Модуль упакован в антистатический пакет. Эта документация также является частью пакета. Внешняя упаковка осуществляется в соответствии с объемом заказа и способом транспортировки в транспортной упаковке, снабженной этикетками и другими данными, необходимыми для транспортировки. Продукт не должен подвергаться воздействию прямых погодных условий во время транспортировки и хранения. Соложение продукта разрешено только в чистых помещениях. без токопроводящей пыли, агрессивных газов и паров. Наиболее подходящая температура хранения - 20 ° C.
Installation
Assembly description	The module C-DM-0001B-SL is mounted in arbitrary positioninto instalation box under a lid or under device located in box.
Connection
Connection of power and system communication	Ribbon flat conductors 0.15 / 0.5 mm2
Connection of inputs / outputs	Strip wires 0.15 / 0.5 mm2
Module operation
Commissioning	The module is operated, set and diagnosed from the MOSAIC programming environment or other parameterization software. The module is ready for operation after connecting the supply voltage and the CIB bus. The HW address is indicated on the label on the module.
Module diagnostics	The basic diagnostics is performed internally and the result is available in the relevant registers of the Mosaic environment.
Maintenance
Description	The module does not require any maintenance under general installation conditions.
Notice	Because the module contains semiconductor components, it is necessary to follow the principles for working with electrostatic sensitive components when handling the removed cover. It is not allowed to directly touch the printed circuit boards without protective measures !!!
Warranty
Generally	Warranty and complaint conditions are governed by the Terms and Conditions of Teco a.s.
Notice	You must meet all the conditions of this documentation before turning on the system. The system must not be put into service unless it has been verified and confirmed that the machinery meets the requirements of Directive 89/392 / EEC, in so far as it applies to it. Documentation subject to change.